How to Replace the Replacement Key Battery For the saab 9-3 key 9-3

Saab owners have a distinct set of steps to add the second key. It requires dealer service with the handheld computer known as Tech-2. Then the transponder must be replaced and a key must be purchased.

Rotate your keys to prevent one from deteriorating faster than the other. This will also ensure that your keys remain in top condition.

Replacement Case

Unlike the classic saab car keys keys of old keys, the latest key fobs are equipped with electronics which makes it hard to copy. This has made stealing cars considerably more difficult than it was years ago. However, it has also made replacing lost keys a much more expensive undertaking.

Saab Car Keys 9-3 owners must have two keys that work. It is costly to replace a lost key because it requires replacing the CIM module, as well as programming the locking cylinders. Dealers charge between $100-$200 to do this.

There are some ways around the high price. Some parts providers will use the code of an old key to cut a brand new metal blade for less than that of a dealer. The key must, however, be the same as the original in order to function in your vehicle.

You can also change the case yourself by following these steps. You'll need a flathead screwdriver as well as some patience. With the screwdriver, break apart the plastic and remove the emergency key. Once the case is open take the electronics out and put them back in your new case. Make sure you put the correct key and badge back in the case too.

Replacement Battery

The saab replacement keys 9-3 replacement battery is a cheap part that can be quickly and easily replaced. This YouTube video by Cyclone Cyd demonstrates how you can replace the remote fob battery with just four steps. This guide should work with any modern saab-type key fob, although the process might differ slightly.

This button is usually located just below the saab spare key logo on the back of the fob. It's usually just below the Saab logo on the back of the fob. Then use an screwdriver with a flat head to insert into the small hole in this button. This should be enough to open the fob's case to allow you to replace the battery.

Once you have installed the batteries CR1632, it is possible to rebuild the remote key fob. Then, you can program it into your car. The entire process shouldn't be more than an hour. It is a very simple process that does not require any special tools.

The procedure is a little more complicated if you've lost your key, but it is possible. The dealer has to first verify the VIN of the vehicle and then order an alternative TWICE module, as well as a key blade with the proper unique code. After that, they will have to cut the replacement key and then program it using the latest software tool known as MDI.

Replacement Key Fob

The key fob contains batteries that are used to lock and unlock your car. Batteries have a limited lifespan and eventually die. This is a typical issue that happens to all cars, and the good news is that you can change the batteries in most key fobs without replacing the entire case. Amazon sells fobs for replacement that already have all the electronic components in place. It is easy to pop the case open and replace the batteries. It is important to remember that you'll need remove the emergency key first, and you can do this by putting the small screwdriver flathead into the slot that is located in the middle of the case. Work the screwdriver around the case, and it should split open, making it simple to remove.

If you're about to replace your keys, ensure that you have spare keys, because this can cut down your total cost by a substantial amount. If you have spare keys, you can request that the dealer cut an additional key and program it into your car, which is cheaper than replacing the whole key fob.

It is possible to add a second key to your vehicle even if you don't have one, but it requires lots of research and work. It costs a few hundred dollars to add a second car key. The computer in the car must also be programmed. Professionals can do this but it's not a cheap option.

Replacement Ignition

Unlike earlier Saab vehicles, the latest SAAB 9-3 models feature a much more sophisticated alarm system that is built on a key code. If you lose your primary key, it could be costly to get another one since the car must be equipped with a specific computer and be programmed to accept a new key. Dealers can even charge hundreds of dollars to program the new key in the event that they are unable to complete the task.

If you've lost only one working key, a dealer will replace the computer in your car (known as the CIM or saab replacement key TWICE) to create the replacement, and will charge you the highest price for it. We can reprogram the current EEPROM of your car's computer so that it is ready to accept an additional key. This will save you more than 50% of the price you'd have to pay an auto dealer.

If you've been a long time owner of a 03-11 SAAB 9-3, then you probably are aware that the ignition key isn't all that durable. They can get extremely sticky, and the buttons are known to be removed from them from time to time and you should think about purchasing a new one if yours isn't working properly. It's not as difficult as it appears to replace the ignition key. With the right tools, it is able to be accomplished quickly.