검색결과
-
[일본] 자민당(自民党), 기업이 직원을 고객의 '카스하라(カスハラ)로부터 보호를 의무로 하는 방안을 고려 중일본 자민당(自民党)에 따르면 기업이 직원을 고객의 '카스하라(カスハラ)로부터 보호를 의무로 하는 방안을 고려 중이다.자민당고용문제조사회의는 2024년 5월16일 기시다 후미오 총리에게 이와 같은 방안을 보고했다. 카스하라는 고객이 직원을 괴롭히는 '고객하라스먼트(カスタマーハラスメント)'의 줄임말이다.기업 경영자가 고객으로부터 괴롭힘을 당하는 직원을 보호하기 위해 노동자보호대책을 강화해야 한다는 입장이다.또한 카스하라에 대한 대책이 명확하지 않은 현실을 고려해 용어의 정의부터 해야 한다고 강조했다. 정부의 지원 강화, 소비자의 교육 등도 대책에 포함된다.과거에 고객 상담과 같은 일부 직종에서 나타나던 카스하라로 직원의 퇴사, 극단적 선택 등으로 이어지며 사회적 이슈로 부상했다.
-
세계 자동차 기능안전 전문가 한국에 모여국가기술표준원(원장 진종욱, 이하 국표원)에 따르면 4월 22일부터 26일까지 5일간 자동차 국제표준 선도를 위해 국제표준화기구 자동차 기능안전*(ISO/TC 22/SC 32/WG 8) 표준 회의가 판교에서 개최된다. 자동차 기능안전 표준 회의에 한국·독일·미국·일본 등 22개국 기능안전 전문가 110여 명이 참여한다. 참고로 기능안전(Functional Safety)이란 전기전자 장치에서 기능상 고장이나 오류가 발생하더라도 시스템이 안전한 상태를 유지하도록 설계하는 기법으로 자동차 분야는 2011년 ISO 26262에 규정으로 제정됐다. 독일을 시작으로 전세계 완성차 업체가 협력사들에 요구하는 자동차 업계의 사실상 의무 기준이다. 자동차 전기전자장치 또는 자율주행 시스템 등의 설계적 결함으로 인한 오작동 및 사고를 방지하기 위해 완성차 업체들은 협력사들에 ISO 26262 등 기능안전 표준 준수를 요구하여 왔다. 최근 자동차 국제규제협의체인 UNECE WP.29*는 자율주행 기능의 안전성 입증을 위해 ISO 26262를 채택했다. UNECE WP.29(UN유럽경제위원회 국제자동차규제조화포럼)는 자동차 및 부품에 대한 국제 규제 부합화 및 국가간 상호인정을 위한 국제기구이다. 167개 선택적용 규정(UN R)과 23개 의무적용 규정(UN GTR)이 존재하며 선택적용 규정도 유럽 등 주요시장 수출을 위해 준수해야 된댜. 국내에서 개최되는 기능안전 표준 회의는 자동차 산업전반에 실효적 영향을 미치는 기능안전 표준에 대한 국내 업계의 높아진 관심을 반영하고 있다. 과거 완성차 업체 등 소수만이 관심을 가졌으나 국제규제 강화에 따라 기능안전 표준 준수가 수출 경쟁력 유지와 직결되어 현재는 전장부품·차량용반도체·SW 등 대부분의 자동차 관련 기업에서 기능안전 표준을 준수하고 있다. 이번 회의에서는 △ISO 26262 제3판 개정 작업 착수 △인공지능(AI) 적용 시 안전확보 방안 △완전자율주행 개념 및 용어 반영 등 최신 기술 이슈들에 대해 12개 파트별로 전세계 전문가들이 논의 예정이다. 한국은 현대자동차 김민성 팀장이‘기능안전 가이드라인 파트’의 리더를 맡아 해당 논의를 이끌게 된다. 진종욱 국표원장은 “자율주행, 인공지능(AI) 등 첨단기술이 도입될수록 자동차의 안전성 확보를 위해 국제표준의 영향력이 증가하고 있으며, 국표원은 국내 업계의 국제표준활동 참여확대와 의견반영을 적극 지원하겠다”고 밝혔다. 다음은 판교에서 개최되고 있는 '국제표준화기구 자동차 기능안전 총회' 개요이다. ■ 국제표준화기구 자동차 기능안전 총회 개요 □ 회의 개요 ○ 행사명: ISO/TC 22/SC 32/WG 8* 제38차 총회 * Road vehicles - Electrical & electronic components & general system aspects - Functional safety 도로차량 기술위원회 - 전기전자부품 및 일반시스템 분과위원회 - 기능안전 작업반 ○ 주최/주관/후원: 국가기술표준원/(사)첨단자동차기술협회/현대자동차(주) ○ 일시/장소: ’24.4.22.(월)~4.26.(금), 그래비티서울판교 스페이스볼룸 ○ 참석자: 한국(현대차, 모비스, 삼성전자, LX세미콘 등), 독일(폭스바겐, 보쉬 등), 미국(포드, GM 등), 일본(토요타, 혼다 등) 등 22개 회원국 전문가 110여명 □ 주요 논의 내용 및 일정 ㅇ (논의 그룹 구조) ISO 26262의 12개 하위 파트별 그룹 및 SOTIF* 파트로 구성 * Safety Of The Intended Functionality(의도된 기능성의 안전)
-
[특집-기술위원회] TC 218 - 목재(Timber)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 등이 있다.ISO/TC 218 목재(Timber)와 관련된 기술위원회는 TC 215, TC 216, TC 217과 마찬가지로 1998년 결성됐다. 사무국은 우크라이나 표준화센터(Ukrainian Scientific Research and Training Center for Standardization, Certification and Quality Problems, UkrNDNC)에서 맡고 있다.위원회는 옥사나 삭(Mrs Oksana Sak)이 책임지고 있다. 현재 의장은 올렉시 치칠리아노(Mr Oleksii Tsytsyliano)이며 임기는 2025년 말까지다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 빈센조 바주치(M Vincenzo Bazzucchi) 등이다.범위는 용어, 사양 및 테스트 방법을 포함해 모든 용도에 사용되는 원형 목재, 제재목 및 가공 목재와 목재 재료의 표준화다. 단, ISO/TC 165 목재 구조물에 포함된 목재의 용도는 제외한다.현재 ISO/TC 218 사무국의 직접적인 책임 하에 발행된 표준은 53개며 ISO/TC 218 사무국의 직접적인 책임 하에 개발 중인 표준은 2개다. 참여하고 있는 회원은 23개국, 참관 회원은 40개국이다.□ ISO/TC 218 사무국의 직접적인 책임 하에 발행된 표준 53개 중 15개 목록▷ISO 631:1975 Mosaic parquet panels — General characteristics▷ISO 737:1975 Coniferous sawn timber — Sizes — Methods of measurement▷ISO 1029:1974 Coniferous sawn timber — Defects — Classification▷ISO 1030:1975 Coniferous sawn timber — Defects — Measurement▷ISO 1031:1974 Coniferous sawn timber — Defects — Terms and definitions▷ISO 1072:1975 Solid wood parquet — General characteristics▷ISO 2036:1976 Wood for manufacture of wood flooring — Symbols for marking according to species▷ISO 2299:1973 Sawn timber of broadleaved species — Defects — Classification▷ISO 2300:1973 Sawn timber of broadleaved species — Defects — Terms and definitions▷ISO 2301:1973 Sawn timber of broadleaved species — Defects — Measurement▷ISO 3129:2019 Wood — Sampling methods and general requirements for physical and mechanical testing of small clear wood specimens▷ISO 4470:1981 Sawn timber — Determination of the average moisture content of a lot▷ISO 4471:1982 Wood — Sampling sample trees and logs for determination of physical and mechanical properties of wood in homogeneous stands▷ISO 4472:1983 Coniferous and broadleaved sawn timber — Transportation packages▷ISO 4475:1989 Coniferous and broadleaved tree sawlogs — Visible defects — Measurement□ ISO/TC 218 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록▷ISO/CD 13061-15 Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 15: Determination of radial and tangential swelling▷ISO/CD 13061-16 Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 16: Determination of volumetric swelling
-
[특집-기술위원회] TC 216 - 신발류(Footwear)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 등이 있다.ISO/TC 216 신발류(Footwear)와 관련된 기술위원회는 TC 215와 마찬가지로 1998년 결성됐다. 사무국은 스페인 표준화협회(Spanish Association for Standardization, UNE)에서 맡고 있다.위원회는 헤나르 아라구조 리베라(Ms Henar Araguzo Rivera)가 책임지고 있다. 현재 의장은 카르멘 아리아스 카스텔라노(Ms Carmen ARIAS CASTELLANO)이며 임기는 2024년 말까지다. ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등이다.범위는 신발 구성품에 대한 테스트 방법, 용어, 성능 요구사항의 표준화다. 또한 신발 전체에 대한 데트스 방법, 용어의 표준화도 포함된다.단, 전문가용 신발(이미 ISO/TC 94에 포함됨) 및 부츠와 신발에 대한 크기 지정 시스템 지정 및 표시(ISO/TC 137에서 다룸) 등은 제외한다.현재 ISO/TC 216 사무국의 직접적인 책임 하에 발행된 표준은 81개며 ISO/TC 216 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 21개국, 참관 회원은 27개국이다.□ ISO/TC 216 사무국의 직접적인 책임 하에 발행된 표준 81개 중 15개 목록▷ISO 10717:2010 Footwear — Test method for slide fasteners — Burst strength▷ISO 10734:2016 Footwear — Test method for slide fasteners — Strength of slide fastener pullers▷ISO 10748:2011 Footwear — Test method for slide fasteners — Slider locking strength▷ISO 10750:2015 Footwear — Test method for slide fasteners — Attachment strength of end stops▷ISO 10751:2016 Footwear — Test methods for slide fasteners — Resistance to repeated opening and closing▷ISO 10764:2016 Footwear — Test methods for slide fasteners — Lateral strength▷ISO 10765:2010 Footwear — Test method for the characterization of elastic materials — Tensile performance▷ISO 10768:2010 Footwear — Test method for the determination of the resistance of elastic materials for footwear to repeated extension — Fatigue resistance▷ISO 16177:2012 Footwear — Resistance to crack initiation and growth — Belt flex method▷ISO/TR 16178:2021 Footwear — Critical substances potentially present in footwear and footwear components — Lists of critical chemical substances▷ISO/TS 16179:2012 Footwear — Critical substances potentially present in footwear and footwear components — Determination of organotin compounds in footwear materials▷ISO 16181-1:2021 Footwear — Critical substances potentially present in footwear and footwear components — Part 1: Determination of phthalate with solvent extraction▷ISO 16181-2:2021 Footwear — Critical substances potentially present in footwear and footwear components — Part 2: Determination of phthalate without solvent extraction▷ISO 16186:2021 Footwear — Critical substances potentially present in footwear and footwear components — Determination of dimethyl fumarate (DMFU)▷ISO 16187:2013 Footwear and footwear components — Test method to assess antibacterial activity□ ISO/TC 216 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 16179 Footwear — Critical substances potentially present in footwear and footwear components — Determination of organotin compounds in footwear materials▷ISO/DIS 16187 Footwear and footwear components — Test method to assess antibacterial activity▷ISO/DIS 19952 Footwear — Vocabulary▷ISO/DTS 20358 Footwear — Performance requirements for components for footwear — Accessories▷ISO/DIS 20537.2 Footwear — Identification of defects during visual inspection — Vocabulary▷ISO/CD 20681 Footwear and footwear components — Test method to assess antimicrobial activity — Agar diffusion test▷ISO/DIS 20686 Footwear — Critical substances potentially present in footwear and footwear components — Determination of certain organic solvents▷ISO/DTS 20939 Footwear — Performance requirements for components for footwear — Outsoles▷ISO/DTS 20952 Footwear — Performance requirements for components for footwear — Uppers▷ISO/DTS 20953 Footwear — Performance requirements for components for footwear — Lining and insocks▷ISO/DTS 20955 Footwear — Performance requirements for components for footwear — Insoles▷ISO/DTS 20961 Footwear — Performance requirements for components for footwear — Shanks▷ISO/DTS 20995 Footwear — Performance requirements for components for footwear — Stiffeners and toe puffs▷ISO/WD 23377 Footwear — Critical substances potentially present in footwear and footwear components — Test method to quantitatively determine certain bisphenols in footwear materials▷ISO/CD TS 23889 Footwear-Performance requirements for components for footwear-Heels and top pieces
-
[특집-기술위원회] TC 214 - 승강기 작업 플랫폼(Elevating work platforms)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 214 승강기 작업 플랫폼(Elevating work platforms)과 관련된 기술위원회는 TC 213과 마찬가지로 1996년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 샐리 사이츠(Ms Sally Seitz)가 책임지고 있다. 현재 의장은 스티븐 A. 베스트(Mr Stephen A. Best)이며 임기는 2029년 말까지다. ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등이다.범위는 용어, 등급, 일반 원칙(기술적 성능 요구 사항 및 위험 평가), 안전 요구사항, 테스트 방법, 유지관리, 승강에 사용되는 작업 플랫폼을 올리기 위한 조작 등의 표준화다. 또한 작업을 수행할 작업 위치에 직원(및 관련 작업 도구, 자재 등)을 배치에 대한 표준화도 포함된다.현재 ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준은 9개며 ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 19개국, 참관 회원은 19개국이다.□ ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준 9개 목록▷ISO 16368:2010 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO 16369:2007 Elevating work platforms — Mast-climbing work platforms▷ISO 16653-1:2008 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 1: MEWPs with retractable guardrail systems▷ISO 16653-2:2021 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 2: MEWPs with non-conductive (insulating) components▷ISO 16653-3:2011 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 3: MEWPs for orchard operations▷ISO 18878:2013 Mobile elevating work platforms — Operator (driver) training▷ISO 18893:2014 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation▷ISO 20381:2009 Mobile elevating work platforms — Symbols for operator controls and other displays▷ISO 21455:2020 Mobile elevating work platforms — Operator's controls — Actuation, displacement, location and method of operation□ ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/FDIS 16368 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO/DIS 18878 Mobile elevating work platforms — Operator (driver) training▷ISO/DIS 18893 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation
-
국제표준화기구, 국제표준화기구(ISO) 내 ‘도시물류 기술위원회’ 설립 확정산업통상자원부 산하 국가기술표준원(원장 진종욱, 이하 국표원)에 따르면 한국이 주도한 국제표준화기구(ISO)내 도시물류(Urban logistics) 기술위원회 설립이 최종 확정됐다.도시물류 기술위원회는 전 세계적인 도시화와 디지털 전환에 대응하기 위해 한국이 주도해 왔으며 프랑스, 독일 등 주요 국가의 지지를 받아 최종 확정됐다.세계 각국은 코로나19 팬데믹 이후 비대면 상거래가 급속히 성장하고 있다. 유통·물류산업에서 경제성, 환경 문제가 이슈화되면서 물류산업 주도를 위해 치열한 경쟁이 펼쳐지고 있다.한국이 발 빠르게 기술위원회 설립을 추진한 이유다. 따라서 국표원은 `23년 1월 국제표준화기구(ISO) 중앙사무국에 신규 설립을 제안했다.전체 회원국 대상 의견 수렴과 설득을 거쳐 지난해 10월 표준화 총회 투표에서 통과됐다. 이후 세부 사항 논의를 거친 결과 3월8일 개최된 제89차 ISO TMB(기술관리이사회) 회의에서 설립이 승인됐다.통상 기술위원회 신설 제안국이 해당 위원회의 의장 및 간사 등 국제 임원을 수임하게 되므로 우리나라가 도시물류 국제표준화 활동을 주도할 것으로 전망된다. 참고로 도시물류(Urban logistics)란 도시 내에서 교통체계, 창고 시설 등 인프라를 활용하여 상품을 소비자에게 신속하고 효율적으로 공급하는 시스템을 말한다.주요 표준화 분야는 △도심형 공동물류센터, 무인매장의 보관, 운송, 유통 분야 △소비자참여 물류(폐기물, 반품 등 역방향 물류) △기술 평가 및 측정, 제품 검사 및 시험방법, 서비스 표준 등이다.다음은 도심물류 기술위원회에 관한 국표원에서 배포한 붙임 내용으로 상세한 내용은 국표원 홈페이지를 참조하면된다. □ 도심물류 기술위원회 개요○ 기술위원회 설립·운영 목표 • 도시 내에서 상품이나 자원 등을 효율적으로 운송, 보관, 분배하는데 필요한 기술과 서비스. 상품이나 자원을 소비자에게 신속하고 효율적으로 공급 ○ 적용 범위 • 도시의 사회적, 경제적, 환경적 발전을 위한 도시물류 기술 및 서비스로 도시물류활동을 위한 표준화된 용어, 기능, 평가, 서비스모델, 수송, 보관 등 도심공급망 기술 등을 포함 ○ 주요 표준화 분야 : 아래 각 분야를 비롯한 다양한 분야로 확장 • 도시물류 기술: 도심형 공동물류센터 (micro fulfillment center), 보관 시스템(self storage, 택배 보관함 포함), 라스트 마일 배송, 무인매장 (스마트스토어, 다크 스토어) 등 효율적인 보관, 운송, 유통을 위한 기술 • 물류 서비스: 경제, 환경, 사회적으로 책임있는 도시 물류 계획 및 실행을 위한 서비스 (예: 소비자참여 물류, 도심 공동 물류, 역(폐기물, 반품)물류 등) • 평가 및 측정: 도시 물류 기술 및 서비스에 대한 용어, 기능, 평가 및 성능 측정 (기술 평가 및 측정, 제품 검사 및 시험방법, 서비스 평가 등) • 기타 도심물류의 가치사슬(Value Chain)에 대응하는 기술 및 서비스 표준 ○ 도시물류 기술 및 서비스 표준 이해당사자(참여 및 활용 대상) • 물류기업에 국한하는 타 TC와 달리 도시물류 기술 및 서비스를 개발하고 사용하며 참여하는 이해당사자는 제조사부터 유통업자, 소비자, 지자체 등 다양 ※ 예 1: 서울교통공사의 생활물류지원센터는 역사 내 공실상가와 유휴공간을 활용해 택배물품 보관, 접수, 픽업, 개인물품 보관 등 생활밀착형 물류서비스를 추진하여 지자체, 공사, 물류기업, 영세상인 등이 모두 참여 ※ 예 2: 다크스토어 (온라인 배송상품만 보관하고 소분하여 배송하는 도심형 물류시설)와 스마트스토어 (무인매장 등) 은 물류와 유통이 혼합된 서비스 형태
-
[특집-기술위원회] TC 206 - 파인 세라믹(Fine ceramics)… 모든 형태의 파인 세라믹 재료 및 제품 분야 표준화스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 등이 있다.ISO/TC 206 파인 세라믹(Fine ceramics)과 관련된 기술위원회는 TC 204, TC 205와 마찬가지로 1992년 결성됐다. 사무국은 일본 산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 히로유키 미야자키(Dr Hiroyuki Miyazaki)가 책임지고 있다. 현재 의장은 이희수 교수(Prof Heesoo Lee)가 맡고 있다.ISO 기술 프로그램 관리자는 츄안유 추(Ms Chuanyu Zou), ISO 편집 관리자는 아룬 ABY 파라에카틸(Mr Arun ABY Paraecattil) 등이다.범위는 모든 형태의 파인 세라믹 재료 및 제품 분야 표준화다. 기계, 열, 화학, 전기, 자기, 광학 및 이들의 조합을 포함한 특정 기능 응용 분야를 위한 분말, 단일체, 코팅 및 복합재 등 모든 형태를 포함하고 있다. 파인 세라믹이라는 용어는 특정 기능적 특성을 지닌 고도로 가공된 고성능, 주로 비금속 무기 재료로 정의된다.참고로 파인 세라믹의 대체 용어는 고급 세라믹, 엔지니어링 세라믹, 테크니컬 세라믹 또는 고성능 세라믹이다. 파인 세라믹(Fine ceramics)은 절연체·내열재·구조재로 쓸수 있도록 고도기술로 개발된 새로운 세라믹을 말한다.현재 ISO/TC 206 사무국의 직접적인 책임 하에 발행된 표준은 156개며 ISO/TC 206 사무국의 직접적인 책임하에 개발 중인 표준은 32개다. 참여하고 있는 회원은 13개국, 참관 회원은 22개국이다.□ ISO/TC 206 사무국의 직접적인 책임 하에 발행된 표준 156개 중 15개 목록▷ISO 3169:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of impurities in aluminium oxide powders using inductively coupled plasma-optical emission spectrometry▷ISO 3180:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of calcium-phosphate-based powders for non-biomedical applications▷ISO 4825-1:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) --Test method for thermal property measurements of metalized ceramic substrates — Part 1: Evaluation of thermal resistance for use in power modules▷ISO 5189:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of metal impurities in silicon dioxide powders using inductively coupled plasma-optical emission spectrometry▷ISO 5618-1:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for GaN crystal surface defects — Part 1: Classification of defects▷ISO 5712:2022 Fine ceramics (advanced ceramics, advanced technical ceramics) — Method for measuring the power generation characteristics of piezoelectric resonant devices for stand-alone power sources▷ISO 5722:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for determining tensile and shear creep of ceramic adhesive▷ISO 5803:2023 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for determination of monoclinic phase in zirconia▷ISO/TS 6857:2024 Fine ceramics (advanced ceramics, advanced technical ceramics) — Physical properties of ceramic composites — Guidelines for determination of void and fibre contents in polished cross section by image analysis▷ISO 10676:2010 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for water purification performance of semiconducting photocatalytic materials by measurement of forming ability of active oxygen▷ISO 10677:2011 Fine ceramics (advanced ceramics, advanced technical ceramics) — Ultraviolet light source for testing semiconducting photocatalytic materials▷ISO 10678:2010 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of photocatalytic activity of surfaces in an aqueous medium by degradation of methylene blue▷ISO 11894-1:2013 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for conductivity measurement of ion-conductive fine ceramics — Part 1: Oxide-ion-conducting solid electrolytes▷ISO 13124:2011 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for interfacial bond strength of ceramic materials▷ISO 13125:2013 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for antifungal activity of semiconducting photocatalytic materials□ ISO/TC 206 사무국의 직접적인 책임 하에 개발 중인 표준 32개 중 15개 목록▷ISO/CD 4255 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic matrix composites at high temperature — Determination of axial tensile properties of tubes▷ISO/AWI 4825-2 Fine ceramics (advanced ceramics, advanced technical ceramics) --Test method for thermal property measurements of metalized ceramic substrates — Part 2: Evaluation of heat transfer characteristics for metalized ceramics substrate for power modules▷ISO/PRF 5618-2 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for GaN crystal surface defects — Part 2: Method for determining etch pit density▷ISO/CD 5770 Fine ceramics (advanced ceramics, advanced technical ceramics) — Relative method for determining thermal conductivity of ceramic coatings▷ISO/DIS 10678 Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of photocatalytic activity of surfaces in an aqueous medium by degradation of methylene blue▷ISO/AWI 10820 Fine ceramics (advanced ceramics, advanced technical ceramics) — Ultraviolet irradiation equipment using UV-A LEDs and optical radiometry for performance test of semiconducting photocatalytic materials▷ISO/DIS 14544 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at high temperature — Determination of compressive properties▷ISO/DIS 14574 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at high temperature — Determination of tensile properties▷ISO/CD 14705 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for hardness of monolithic ceramics at room temperature▷ISO/WD 15733 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure — Determination of tensile properties▷ISO/AWI 17138 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of ceramic composites at room temperature — Determination of flexural strength▷ISO/AWI 17561 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test methods for dynamic elastic moduli of monolithic ceramics at room temperature by sonic resonance and Impulse Excitation Technique (IET)▷ISO/CD 17590 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods of tests for reinforcements — Determination of the tensile properties of ceramic filaments at elevated temperature in air using the hot grip technique▷ISO/AWI 17947-1 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of fine silicon nitride powders — Part 1: Wet chemical methods, X-ray fluorescence (XRF) using the fused cast-bead method, carrier-gas hot extraction (CGHE) and combustion methods▷ISO/AWI 18719 Fine ceramics (advanced ceramics, advanced technical ceramics) — Methods for chemical analysis of impurities in yttrium oxide powders using inductively coupled plasma-optical emission spectrometry
-
[특집-기술위원회] TC 205 - 건축 환경 디자인(Building environment design)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 등이 있다.ISO/TC 205 건축 환경 디자인(Building environment design)과 관련된 기술위원회는 TC 204와 마찬가지로 1992년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 라이언 섄리(Mr Ryan Shanley)가 책임지고 있다. 현재 의장은 드레이크 에르베(Mr Drake Erbe)이며 임기는 2025년말 까지다.ISO 기술 프로그램 관리자는 스테판 소바쥬(M Stéphane Sauvage), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등이다.범위는 수용 가능한 실내 환경 및 실행 가능한 에너지 절약, 효율성을 위해 신규 건물의 설계 및 기존 건물 개조에 관한 표준화다.건축 환경 설계는 기술적 건축 시스템 및 관련 건축 측면을 다루며 관련 설계 프로세스, 설계 방법, 설계 결과 및 설계 단계 건물 커미셔닝을 포함하고 있다. 실내 환경에는 공기질과 열, 음향, 시각적 요소가 포함된다. 다음 내용들도 표준화에 포함된다.세부적으로 보면 △건물 설계 및 기존 건물 개조 설계에서 다룰 수 있는 실내 환경 품질 및 에너지와 관련된 지속 가능성 측면 △건축 환경 설계의 일반 원칙 △에너지 효율적인 건물 설계 △건물 및 개조 설계의 건물 자동화 및 제어 시스템 △건물 및 개조 설계의 실내 공기질 △건물의 실내 열 환경 및 개조 설계 △건물 및 개조 설계의 실내 음향 환경 △건물의 실내 시각적 환경 및 개조 설계 △복사를 포함한 냉난방 시스템 설계 △새 건물 및 개조 설계에 건물 환경 장비의 성능을 테스트하고 평가하는 방법의 적용 등이다.전체적인 접근 방식을 사용하는 ISO/TC163/WG4 공동 작업 그룹 TC 163 및 TC 205 에너지 성능 ISO/TC163/WG4 Joint working group TC 163 & TC 205 Energy performance)을 통해 ISO/TC 163과의 긴밀한 협력을 통해 건물 개조 뿐 아니라 신규 및 기존 건물의 에너지 성능에 관한 전체적인 평가의 표준화도 포함된다.표준화에는 △용어 및 정의 △건물 및 기술 시스템의 시스템 경계 △건축 요소의 에너지 성능을 고려한 건물의 전반적인 에너지 성능 평가 △건물 관련 시스템(난방, 냉방, 가정용 온수, 환기, 조명, 시스템 제어, 운송 및 기타 에너지 관련 시스템) △실내 및 실외 조건 △지역 에너지 생산(현장 및 지역 수준) △(사용) 에너지원(재생 가능 포함) △건물 커미셔닝 △전반적인 에너지 효율 평가 △건축물의 에너지 성능 및 에너지 성능 인증을 나타내는 수단 등이 있다.다만 △기타 인체공학적 요인 △대기 오염물질과 열, 음향 및 조명 특성을 측정하는 방법 △건축 환경의 열 성능 및 에너지 사용(ISO TC 163) △기존 건물의 건물 환경 장비 성능 및 등급을 테스트하는 방법 △기존 건물을 검사하거나 평가 △건설 등은 제외한다.현재 ISO/TC 205 사무국의 직접적인 책임 하에 발행된 표준은 49개며 ISO/TC 205 사무국의 직접적인 책임하에 개발 중인 표준은 10개다. 참여하고 있는 회원은 26개국, 참관 회원은 34개국이다.□ ISO/TC 205 사무국의 직접적인 책임 하에 발행된 표준 49개 중 15개 목록▷ISO 11855-1:2021 Building environment design — Embedded radiant heating and cooling systems — Part 1: Definitions, symbols, and comfort criteria▷ISO 11855-1:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 1: Definitions, symbols, and comfort criteria — Amendment 1▷ISO 11855-2:2021 Building environment design — Embedded radiant heating and cooling systems — Part 2: Determination of the design heating and cooling capacity▷ISO 11855-2:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 2: Determination of the design heating and cooling capacity — Amendment 1▷ISO 11855-3:2021 Building environment design — Embedded radiant heating and cooling systems — Part 3: Design and dimensioning▷ISO 11855-3:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 3: Design and dimensioning — Amendment 1▷ISO 11855-4:2021 Building environment design — Embedded radiant heating and cooling systems — Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS)▷ISO 11855-4:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) — Amendment 1▷ISO 11855-5:2021 Building environment design — Embedded radiant heating and cooling systems — Part 5: Installation▷ISO 11855-5:2021/Amd 1:2023 Building environment design — Embedded radiant heating and cooling systems — Part 5: Installation — Amendment 1▷ISO 11855-6:2018 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 6: Control▷ISO 11855-6:2018/Amd 1:2023 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 6: Control — Amendment 1▷ISO 11855-7:2019 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 7: Input parameters for the energy calculation▷ISO 11855-7:2019/Amd 1:2024 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 7: Input parameters for the energy calculation — Amendment 1▷ISO 11855-8:2023 Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 8: Electrical heating systems□ ISO/TC 205 사무국의 직접적인 책임 하에 개발 중인 표준 10개 목록▷ISO/TR 5863 Integrative design of the building envelope — General principles▷ISO/DIS 16484-2 Building automation and control systems (BACS) — Part 2: Hardware▷ISO/DIS 16484-4 Building automation and control systems (BACS) — Part 4: Control applications▷ISO/DIS 16813 Building environment design — Indoor environment — General principles▷ISO/WD 20734 Building Enviroment Design — Daylighting design procedure for indoor visual environment▷ISO/WD 21075 Design and assessment process of whole-building mechanical ventilation systems in residential buildings▷ISO/WD 22511-1 Design process of ventilative cooling systems — Part 1: Non-residential buildings▷ISO/AWI TS 23764 Methodology for achieving non-residential zero-energy buildings (ZEBs)▷ISO/CD 24359-1 Building commissioning process planning — Part 1: New buildings▷ISO/AWI TR 52032-2 Energy performance of buildings — Energy requirements and efficiencies of heating, cooling and domestic hot water (DHW) distribution systems — Part 2: Explanation and justification of ISO 52032-1
-
[특집-기술위원회] TC 199 - 기계류 안전(Safety of machinery)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 등이 있다.ISO/TC 199 기계류 안전(Safety of machinery)과 관련된 기술위원회는 1991년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 크리스티안 톰(Mr Dr. rer. nat Christian Thom)가 책임지고 있다. 현재 의장은 오토 괴르네만(Mr Otto Görnemann)이다.ISO 기술 프로그램 관리자는 메르세 페레 에르난데스(Mme Mercè Ferrés Hernández), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등이다.범위는 ISO/IEC 가이드 51 프레임워크 및 ISO, IEC 기술 위원회와 협력해 용어, 방법론, 보호 장치 및 안전 장치를 통합한 기계 안전에 대한 기본 개념 및 일반 원칙의 표준화다.단, ISO/IEC Guide 51에 정의되어 있고 다른 ISO 또는 IEC 기술 위원회의 작업에서 명시적으로 다루고 있는 제품 안전 표준은 제외한다.현재 ISO/TC 199 사무국의 직접적인 책임 하에 발행된 표준은 45개며 ISO/TC 199 사무국의 직접적인 책임 하에 개발 중인 표준은 9개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 199 사무국의 직접적인 책임 하에 발행된 표준 45개 중 15개 목록▷ISO Guide 78:2012 Safety of machinery — Rules for drafting and presentation of safety standards▷ISO 11161:2007 Safety of machinery — Integrated manufacturing systems — Basic requirements▷ISO 11161:2007/Amd 1:2010 Safety of machinery — Integrated manufacturing systems — Basic requirements — Amendment 1▷ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction▷ISO 13849-1:2023 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design▷ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation▷ISO 13850:2015 Safety of machinery — Emergency stop function — Principles for design▷ISO 13851:2019 Safety of machinery — Two-hand control devices — Principles for design and selection▷ISO 13854:2017 Safety of machinery — Minimum gaps to avoid crushing of parts of the human body▷ISO 13855:2010 Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body▷ISO 13856-1:2013 Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors▷ISO 13856-2:2013 Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars▷ISO 13856-3:2013 Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices▷ISO 13857:2019 Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs▷ISO 14118:2017 Safety of machinery — Prevention of unexpected start-up□ ISO/TC 199 사무국의 직접적인 책임 하에 개발 중인 표준 9개 목록▷ISO/AWI 12100 Safety of machinery — General principles for design — Risk assessment and risk reduction▷ISO/DIS 12895 Safety of machinery — Identification of whole body access and prevention of associated risk(s)▷ISO/AWI 13849-2 Safety of machinery — Safety-related parts of control systems — Part 2: Guidance for the design and validation▷ISO/AWI TR 13849-3 Safety of machinery — Safety-related parts of control systems — Part 3: Markov model-based PFH calculation▷ISO/FDIS 13855 Safety of machinery — Positioning of safeguards with respect to the approach of the human body▷ISO/FDIS 14119 Safety of machinery — Interlocking devices associated with guards — Principles for design and selection▷ISO/AWI 14122-1 Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means of access between two levels▷ISO/AWI 14159 Safety of machinery — Hygiene requirements for the design of machinery▷ISO/CD TR 21260 Safety of machinery — Mechanical safety data for physical contacts between moving machinery or moving parts of machinery and persons
-
[특집-기술위원회] TC 193 - 천연가스(Natural gas)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 등이 있다.ISO/TC 193 천연가스(Natural gas)와 관련된 기술위원회는 TC 192와 마찬가지로 1988년 결성됐다. 사무국은네덜란드 표준화기구(Royal Netherlands Standardization Institute, NEN)에서 맡고 있다.위원회는 니콜렛 바스(Ms Nicolet Baas)이 책임지고 있다. 현재 의장은 아드리안 반 데르 빈(Mr Adriaan van der Veen)이며 임기는 2024년 말까지다. ISO 기술 프로그램 관리자는 키르시 실란데르-반 후넨(Mrs Kirsi Silander-van Hunen), ISO 편집 관리자는 루시 커크(Ms Lucy Kirk)등으로 조사됐다.범위는 아래와 같은 열물리적 특성 계산 및 측정을 포함한 용어, 품질 사양, 측정 방법, 샘플링, 분석 및 테스트 등의 표준화다.- 아래 - ○ 천연 가스○ 천연가스 대체품○ 천연 가스와 가스 연료(예: 비전통 가스 및 재생 가스)의 혼합물 습식 가스○ 생산부터 국경을 넘어 가능한 모든 최종 사용자에게 배송까지 모든 측면○ 액화천연가스(LNG) 분석 방법의 표준화 등도 포함된다. 또한 다른 기술위원회 및 이들 기술위원회와 연계한 천연가스 관련 작업을 인정한다.현재 ISO/TC 193 사무국과 관련해 발행된 표준은 62개며 ISO/TC 193의 직접적인 책임 하에 발행된 표준은 10개다. ISO/TC 193 사무국과 관련해 개발 중인 표준은 19개며 ISO/TC 193의 직접적인 책임 하에 개발 중인 표준은 7개다. 참여하고 있는 회원은 29개국, 참관 회원은 28개국이다.□ ISO/TC 193 사무국의 직접적인 책임 하에 발행된 표준 10개 목록▷ISO 13443:1996 Natural gas — Standard reference conditions▷ISO 13443:1996/Cor 1:1997 Natural gas — Standard reference conditions — Technical Corrigendum 1▷ISO 13686:2013 Natural gas — Quality designation▷ISO 13734:2013 Natural gas — Organic components used as odorants — Requirements and test methods▷ISO 14532:2014 Natural gas — Vocabulary▷ISO 15112:2018 Natural gas — Energy determination▷ISO 15403-1:2006 Natural gas — Natural gas for use as a compressed fuel for vehicles — Part 1: Designation of the quality▷ISO 15970:2008 Natural gas — Measurement of properties — Volumetric properties: density, pressure, temperature and compression factor▷ISO 15971:2008 Natural gas — Measurement of properties — Calorific value and Wobbe index▷ISO/TS 16922:2022 Natural gas — Odorization□ ISO/TC 193 사무국의 직접적인 책임 하에 개발 중인 표준 7개 목록▷ISO/CD TR 5268 Odorants and Odor character▷ISO/AWI 14111 Natural gas — Guidelines to metrological traceability▷ISO/AWI 14532 Natural gas — Vocabulary▷ISO/CD 17507-1 Natural gas — Calculation of methane number of gaseous fuels for reciprocating internal combustion engines — Part 1: MNc method▷ISO/CD 17507-2 Natural gas — Calculation of methane number of gaseous fuels for reciprocating internal combustion engines — Part 2: PKI method▷ISO/DTS 18222.2 Natural gas — Correlation between odorant concentration in air and odour intensity▷ISO/AWI 23219 Natural gas — Format for data from gas chromatograph analysers for natural gas — XML file format□ ISO/TC 193 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 193/SC 1 Analysis of natural gas ; 발행된 표준 46개, 개발 중인 표준 8개▷ISO/TC 193/SC 3 Upstream area ; 발행된 표준 6개, 개발 중인 표준 4개