검색결과
-
[특집-기술위원회] TC 130 - 그래픽 기술(Graphic technology)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127 등도 포함된다.ISO/TC 130 그래픽 기술(Graphic technology)과 관련된 기술위원회는 1969년 결성됐다. 사무국은 중국 국가표준화관리위원(国家标准化管理委员会, Standardization Administration of China, SAC)에서 맡고 있다.위원회는 메이팡 리(Ms Meifang Li)가 책임지고 있다. 현재 의장은 펑페이 짜오(Mr Pengfei Zhao)로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 인쇄 및 그래픽 기술 분야의 표준화를 다루고 있다. 이 분야는 그래픽 요소(이미지, 텍스트, 라인 아트, 패턴 등)가 생성, 조작, 조립, 전달되고 최종적으로 디지털 제품으로 전자적으로 전달되거나 잉크, 토너 및 기타를 사용해 물리적으로 기판에 전달되는 프로세스의 모든 단계를 다룬다. 마킹 또는 기능성 재료를 생산하고 최종 응용 분야의 요구에 따라 마감 처리된다.ISO/TC 130 표준에는 용어, 시각적 외관 및 제품 품질 평가, 데이터 교환, 프로세스 제어, 관리, 적합성 평가, 환경에 대한 영향 등이 포함되지만 이에 국한되지는 않는다. 뿐만 아니라 관련 재료, 장비 및 시스템에 대한 요구 사항 및 테스트도 수용한다.참고로 ISO/TC 42, TC 6, TC 256, TC 35, IEC/TC 100 및 ISO/IEC JTC 1/SC 28과 같은 다른 TC/SC와 범위가 실제 또는 잠재적으로 중복되는 경우 관련 TC와의 연락 또는 JWG를 통한 조정은 유지되거나 적극적으로 추진돼야 한다.현재 ISO/TC 130 사무국과 관련해 발행된 표준은 115개며 ISO/TC 130 사무국과 관련해 개발 중인 표준은 15개다. 참여하고 있는 회원은 21개국, 참관 회원은 22개국이다.□ ISO/TC 130 사무국 분과위원회(Subcommittee)의 책임 하에 발행된 표준 115개 중 15개 목록▷ISO 2834-1:2020 Graphic technology — Laboratory preparation of test prints — Part 1: Paste inks▷ISO 2834-2:2022 Graphic technology — Laboratory preparation of test prints — Part 2: Liquid printing inks▷ISO 2834-3:2008 Graphic technology — Laboratory preparation of test prints — Part 3: Screen printing inks▷ISO 2836:2021 Graphic technology — Prints and printing inks — Assessment of resistance of prints to various agents▷ISO 2846-1:2017 Graphic technology — Colour and transparency of printing ink sets for four-colour printing — Part 1: Sheet-fed and heat-set web offset lithographic printing▷ISO 2846-2:2007 Graphic technology — Colour and transparency of printing ink sets for four-colour printing — Part 2: Coldset offset lithographic printing▷ISO 5776:2022 Graphic technology — Symbols for text proof correction▷ISO/TS 10128:2009 Graphic technology — Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data▷ISO 11084-1:1993 Graphic technology — Register systems for photographic materials, foils and paper — Part 1: Three-pin systems▷ISO 11084-2:2006 Graphic technology — Register systems for photographic materials, foils and paper — Part 2: Register pin systems for plate making▷ISO 12040:1997 Graphic technology — Prints and printing inks — Assessment of light fastness using filtered xenon arc light▷ISO 12218:1997 Graphic technology — Process control — Offset platemaking▷ISO 12632:2015 Graphic technology — Ink, paper and labels — Requirements on hot alkali penetration and resistance▷ISO 12634:2017 Graphic technology — Determination of tack of paste inks and vehicles by a rotary tackmeter▷ISO 12635:2021 Graphic technology — Plates for offset printing — Dimensions□ ISO/TC 130 사무국 분과위원회(Subcommittee)의 책임 하에 개발 중인 표준 15개 목록▷ISO/DTS 10128 Graphic technology — Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data▷ISO/DIS 12641-1 Graphic technology — Prepress digital data exchange — Colour targets for input scanner calibration — Part 1: Colour targets for input scanner calibration▷ISO/FDIS 12643-1.2 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 1: General requirements▷ISO/FDIS 12643-2.2 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 2: Prepress and press equipment and systems▷ISO/FDIS 12643-3 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 3: Binding and finishing equipment and systems▷ISO/FDIS 12643-4 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 4: Converting equipment and systems▷ISO/FDIS 12643-5 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 5: Manually-fed stand-alone platen presses▷ISO/DIS 12647-2 Graphic technology — Process control for the production of half-tone colour separations, proof and production prints — Part 2: Offset lithographic processes▷ISO/AWI 15076-2 Image technology colour management — Architecture, profile format and data structure — Part 2: Based on ICC.1:2022▷ISO/DIS 15339-1 Graphic technology — Printing from digital data across multiple technologies — Part 1: Principles▷ISO/AWI TS 18621-22 Graphic technology — Image quality evaluation methods for printed matter — Part 22: Evaluation of colour graininess▷ISO/DTS 18621-31 Graphic technology — Image quality evaluation methods for printed matter — Part 31: Evaluation of the perceived resolution of printing systems with the Contrast–Resolution chart▷ISO/AWI 19307 Graphic Technology — Measurement and one-parameter representation of translucency▷ISO/CD TR 23805 Graphic technology — Dry back calculation for offset printing process▷ISO/FDIS 24487 Graphic technology — Processless lithographic plates — Evaluation methods for characteristics and performance□ ISO/TC 130 사무국의 작업그룹(Working Group, WG) 현황▷ISO/TC 130/JWG 7 Joint TC 130 - ICC WG: colour management▷ISO/TC 130/JWG 14 Joint TC 130 - TC 42 - ISO/IEC JTC 1/SC 28 WG: Print quality measurement methods▷ISO/TC 130/TF 3 Communications▷ISO/TC 130/WG 1 Terminology▷ISO/TC 130/WG 2 Prepress data exchange▷ISO/TC 130/WG 3 Process control and related metrology▷ISO/TC 130/WG 4 Media and materials▷ISO/TC 130/WG 5 Ergonomics - Safety▷ISO/TC 130/WG 10 Management of security printing processes▷ISO/TC 130/WG 11 Environmental impact of graphic technology▷ISO/TC 130/WG 12 Postpress
-
[기획-디지털 ID 기술] ⑲소닉월, '무선 메시 네트워크에서 탄성 보안 서비스 및 로드 밸런싱' 명칭의 미국 특허 등록 (US 11729621)미국 사이버 보안 기업 소닉월(SONICWALL)에 따르면 2023년 8월15일 '무선 메시 네트워크에서 탄성 보안 서비스 및 로드 밸런싱(Elastic security services and load balancing in a wireless mesh network)' 명칭의 미국 특허(US 11729621)가 등록됐다.본 등록 특허는 2019년 4월29일 출원된(US 16/397951) 후 2022년 4월19일 등록된 원출원건(US 2020-0344610)을 우선권 주장해 2022년 4월 8일에 출원됐다(US 17/716860).본 등록 특허의 패밀리 특허에는 3건의 미국 특허(US 11310665, US 11438963, US 11540132)가 등록됐고, 2건의 미국 특허(US 2022-0418041, US 2023-0209350)가 심사 중이다. 본 등록 특허는 무선 네트워크에서 상이한 노드 전반에 걸쳐 처리 능력을 분배하는 시스템에 관한 특허다.특히 서로 다른 무선 노드가 각각의 무선 노드와 연관된 캐시에서 요청된 콘텐츠에 관한 콘텐츠 등급을 수신하고 저장하도록 함으로써 네트워크 내의 다른 노드로의 통신 전달 필요성을 최소화한다. 이를 통해 무선 네트워크에서 통신 효율을 증가시킬 수 있다.또한 본 등록 특허는 메시징 트래픽을 증가시키지 않고 무선 네트워크에서 콘텐츠 등급을 다른 노드에 분배하기 때문에 로드 밸런싱 기능을 수행한다.액세스 요청에 관한 응답 메시지가 요청자에게 다시 전달됨에 따라, 통신 경로를 따르는 노드에서의 캐시 메모리는 수신된 콘텐츠 등급을 가진 데이터 식별자를 참조하는 정보를 포함하도록 업데이트된다.상기 교차 참조된 데이터 식별자 및 콘텐츠 등급은 통신 경로를 따라 각 무선 노드가 불량 콘텐츠에 대한 요청을 차단할 수 있게 허용한다.
-
산업부, ‘2023년 세계 표준의 날’ 기념식 개최국제표준 공동개발 및 국제포럼 운영 등 국제표준화 활동이 확대될 전망이다. 이에 국내 기업의 기술혁신과 세계시장 선점이 기대된다. 산업통상자원부는 12일 대한상공회의소에서 ‘2023년 세계 표준의 날’ 기념식을 개최하고 국내외 표준화 활동 유공자·단체를 대상으로 총 40점의 포상을 수여했다고 밝혔다. 포상으로는 산업훈장 1점(동탑), 산업포장 1점, 대통령 표창 4점, 국무총리 표창 4점, 장관 표창 30점 등이다. 세계 표준의 날(10월 14일)은 1970년 3대 국제표준화기구에서 표준의 중요성을 알리고 국제표준을 확산하고자 지정한 날로 우리나라는 2000년부터 이날을 기념하기 위해 유공자 포상 수여 등의 행사를 진행하고 있다. 3대 국제표준화기구는 ISO(국제표준화기구), IEC(국제전기기술위원회), ITU(국제전기통신연합)다. 이날 기념식에서 박주면 ㈜제로엔 대표이사는 세계 최초로 에너지 분야 탄소중립 이행을 위한 국제표준을 주도적으로 개발한 공로로 동탑산업훈장을 수상했다. 해당 표준은 공장, 건물 등의 넷제로(Net Zero) 에너지의 범위, 에너지 효율 관리, 신재생에너지 적용 등의 원칙 등을 제시하고 있어 우리 기업들의 탄소중립 실현을 위한 가이드가 될 것으로 기대된다. 넷제로 에너지는 소비되는 에너지와 생산되는 신재생에너지가 일치하여 그 차이가 ‘0’이 되는 상태를 말한다. 더불어 김형준 한국전자통신연구원 연구위원은 국제표준화기구 의장단 활동을 통해 사물인터넷, 스마트시티 등 지능화 융합 서비스 분야 표준개발 및 확산에 기여한 공로로 산업포장을 수상했다. 장영진 산업부 1차관은 “우리 기업의 기술혁신과 세계시장 선점을 위해 첨단기술 분야별 표준화 전략을 수립하고, 미국·독일 등 주요 국가와의 국제표준 공동개발 및 국제포럼 운영 등 적극적인 국제표준화 활동을 확대해 나가겠다”고 밝혔다.
-
[특집-공동기술위원회] ⑥ISO/IEC JTC 1/SC 7 소프트웨어 및 시스템 엔지니어링(Software and systems engineering) 소개 - 1스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(Working Group, WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등을 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.또한 국제전기기술위원회(International Electro-technical Commission, IEC)는 전기 및 전자 제품의 고품질 인프라와 국제 무역을 뒷받침하는 글로벌 비영리 회원조직이다.기술 혁신, 저렴한 인프라 개발, 효율적이고 지속 가능한 에너지 접근, 스마트 도시화 및 교통 시스템, 기후 변화 완화를 촉진하고 사람과 환경의 안전을 향상시키는 역할을 수행하고 있다. 170개 이상의 국가를 통합하고 전 세계 2만 명의 전문가에게 글로벌하고 중립적이며 독립적인 표준화 플랫폼을 제공한다. 장치, 시스템, 설치, 서비스 및 인력이 필요에 따라 작동함을 구성원이 인증하는 4가지 적합성 평가 시스템을 관리한다.적합성 평가와 함께 정부가 국가 품질 인프라를 구축한다. 모든 규모의 기업이 전 세계 대부분의 국가에서 일관되게 안전하고 신뢰할 수 있는 제품을 사고 팔 수 있도록 하는 기술 프레임워크를 제공하는 약 1만개의 IEC 국제표준을 발행하고 있다.이러한 ISO와 IEC가 공동으로 구성한 기술위원회 ISO/IEC JTC 1 정보 기술(Information technology)에 대해 살펴볼 예정이다. JTC 1은 1987년 결성됐으며 사무국은 미국국립표준협회(American National Standards Institute, ANSI)에서 맡고 있다. 위원회는 리사 라지첼(Mrs Lisa Rajchel)가 책임지고 있다. 현재 의장은 필 웬블롬(Mr Phil Wennblom)으로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), 스티븐 더트널(Mr Stephen Dutnall), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등으로 조사됐다. 범위는 정보기술 분야의 표준화다.현재 ISO/IEC JTC 1의 직접적인 책임 하에 발행된 표준은 517개며 직접적인 책임 하에 개발 중인 표준은 23개다. 참여하고 있는 회원은 40개국, 참관 회원은 62개국이다.공동 기술위원회(Joint Technical Committee, JTC) 산하에서 활동하고 있는 분과위원회(Subcommittee, SC) 중 SC 1, SC 2, SC 6에 이어 SC 7에 대해 살펴보면 다음과 같다.ISO/IEC JTC 1/SC 7 소프트웨어 및 시스템 엔지니어링(Software and systems engineering)과 관련된 분과위원회는 1987년 결성됐다. 사무국은 인도 표준국(Bureau of Indian Standards, BIS)에서 맡고 있다.위원회는 레나 가르그(Ms Reena Garg)이 책임지고 있다. 현재 의장은 선딥 오베로이(Dr Sundeep Oberoi)으로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), ISO 편집 관리자는 이본느 헨(Mrs Yvonne Chen) 등으로 조사됐다.범위는 소프트웨어 제품 및 시스템 엔지니어링을 위한 프로세스, 지원 도구 및 지원 기술의 표준화다. 참고로 프로세스, 도구 및 기술은 JTC 1 참조 약관의 범위 내에 있으며 JTC 1이 다른 SC에 할당한 특정 도구 및 기술은 제외된다.현재 ISO/IEC JTC 1/SC 7 사무국의 직접적인 책임 하에 발행된 표준은 212개며 개발 중인 표준은 41개다. 참여하고 있는 회원은 37개국, 참관 회원은 24개국이다.□ ISO/IEC JTC 1/SC 7 사무국의 직접적인 책임하에 발행된 표준 및(또는) 프로젝트 212개 중 15개 목록▷ISO 5806:1984 Information processing — Specification of single-hit decision tables▷ISO 5807:1985 Information processing — Documentation symbols and conventions for data, program and system flowcharts, program network charts and system resources charts▷ISO/IEC TR 7052:2023 Software engineering — Controlling frequently occurring risks during development and maintenance of custom software▷ISO/IEC 8631:1989 Information technology — Program constructs and conventions for their representation▷ISO 8790:1987 Information processing systems — Computer system configuration diagram symbols and conventions▷ISO 8807:1989 Information processing systems — Open Systems Interconnection — LOTOS — A formal description technique based on the temporal ordering of observational behaviour▷ISO/IEC TR 10000-1:1998 Information technology — Framework and taxonomy of International Standardized Profiles — Part 1: General principles and documentation framework▷ISO/IEC 10746-1:1998 Information technology — Open Distributed Processing — Reference model: Overview — Part 1:▷ISO/IEC 10746-2:2009 Information technology — Open distributed processing — Reference model: Foundations — Part 2:▷ISO/IEC 10746-3:2009 Information technology — Open distributed processing — Reference model: Architecture — Part 3:▷ISO/IEC 10746-4:1998 Information technology — Open Distributed Processing — Reference Model: Architectural semantics — Part 4:▷ISO/IEC 10746-4:1998/Amd 1:2001 Information technology — Open Distributed Processing — Reference Model: Architectural semantics — Part 4: — Amendment 1: Computational formalization▷ISO/IEC 11411:1995 Information technology — Representation for human communication of state transition of software▷ISO/IEC TR 12182:2015 Systems and software engineering — Framework for categorization of IT systems and software, and guide for applying it▷ISO/IEC/IEEE 12207-2:2020 Systems and software engineering — Software life cycle processes — Part 2: Relation and mapping between ISO/IEC/IEEE 12207:2017 and ISO/IEC 12207:2008□ ISO/IEC JTC 1/SC 7 사무국의 직접적인 책임하에 개발중인 표준 및(또는) 프로젝트 41개 중 15개 목록▷ISO/IEC CD 9837-1 Software and systems engineering — Systems resilience — Part 1: Concepts and vocabulary▷ISO/IEC/IEEE 15026-3 Systems and software engineering — Systems and software assurance — Part 3: System integrity levels▷ISO/IEC CD 19770-5 Information technology — IT asset management — Part 5: Overview and vocabulary▷ISO/IEC PRF 19770-6 Information technology — IT asset management — Part 6: Hardware identification tag▷ISO/IEC CD TS 19770-10 Information technology — IT asset management — Part 10: Guidance for implementing ITAM▷ISO/IEC CD 20582 Software and systems engineering — Capabilities of build and deployment tools▷ISO/IEC AWI TR 24586-1 Software and systems engineering — Agile and DevOps principles and practices — Part 1: Agile principles and practices▷ISO/IEC AWI TR 24586-2 Software and systems engineering — Agile and DevOps principles and practices — Part 2: DevOps principles and practices▷ISO/IEC/IEEE FDIS 24748-1 Systems and software engineering — Life cycle management — Part 1: Guidelines for life cycle management▷ISO/IEC/IEEE FDIS 24748-2 Systems and software engineering — Life cycle management — Part 2: Guidelines for the application of ISO/IEC/IEEE 15288 (System life cycle processes)▷ISO/IEC DIS 24773-2 Software and systems engineering — Certification of software and systems engineering professionals — Part 2: Guidance regarding description of knowledge, skills, and competencies contained in schemes▷ISO/IEC DIS 25002 Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Quality models overview and usage▷ISO/IEC FDIS 25010 Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Product quality model▷ISO/IEC PRF 25019 Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Quality-in-use model▷ISO/IEC DIS 25040 Systems and software engineering – Systems and software Quality Requirements and Evaluation (SQuaRE) – Quality evaluation framework
-
[기획-디지털 ID 기술] ⑮어도비, '딥 인지 속성 신경망을 사용하는 다수의 속성 그룹으로부터 디지털 속성 식별' 명칭의 미국 특허 등록(US 11734337)미국 컴퓨터 소프트웨어 기업 어도비(Adobe Inc)에 따르면 2023년 8월22일 '딥 인지 속성 신경망을 사용하는 다수의 속성 그룹으로부터 디지털 속성 식별(Identifying digital attributes from multiple attribute groups utilizing a deep cognitive attribution neural network)' 명칭의 미국 특허(US 11734337)가 등록됐다.본 등록 특허는, 2019년 9월9일 출원돼(US 16/564831) 2022년 7월12일 등록된 원출원건(US 11386144)으로부터 2022년 6월14일 계속 출원됐다.본 등록 특허는 '객체의 예측된 속성에 기초해 디지털 이미지에 묘사된 객체에 대한 태그를 생성하기 위한 시스템 및 방법'에 관한 것이다.본 등록 특허의 일실시예에 따르면 교번 인셉션 계층과 확장된 컨볼루션 층의 인터리빙된 신경망 계층을 사용하여 로컬화 특징 벡터(localization feature vector)를 생성할 수 있다. 로컬화 특징 벡터에 기초해 글로벌 평균 풀링 층과 같은 일부 풀링 계층을 사용하며 속성 로컬화 특징 임베딩(attribute localization feature embeddings)을 생성할 수 있다.예측된 속성을 바탕으로 상기 속성 로컬화 특징 임베딩을 해당 속성 그룹 분류기들에 적용해 태그를 생성할 수 있다. 특히, 속성 그룹 분류기들은 쿼리 이미지와 연관된 속성들을 예측할 수 있다. 상기 생성된 태그에 기초해 태그 쿼리 및 검색 쿼리에 응답하여 응답할 수 있다.
-
[특집-공동기술위원회] ⑤JTC 1/SC 6 시스템 간 통신 및 정보 교환(Telecommunications and information exchange between systems)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(Working Group, WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등을 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.또한 국제전기기술위원회(International Electro-technical Commission, IEC)는 전기 및 전자 제품의 고품질 인프라와 국제 무역을 뒷받침하는 글로벌 비영리 회원 조직이다.기술 혁신, 저렴한 인프라 개발, 효율적이고 지속 가능한 에너지 접근, 스마트 도시화 및 교통 시스템, 기후 변화 완화를 촉진하고 사람과 환경의 안전을 향상시키는 역할을 수행하고 있다. 170개 이상의 국가를 통합하고 전 세계 2만명의 전문가에게 글로벌하고 중립적이며 독립적인 표준화 플랫폼을 제공하고 있다. 장치, 시스템, 설치, 서비스 및 인력이 필요에 따라 작동함을 구성원이 인증하는 4가지 적합성 평가 시스템을 관리한다.적합성 평가와 함께 정부가 국가 품질 인프라를 구축하고 모든 규모의 기업이 전 세계 대부분의 국가에서 일관되게 안전하고 신뢰할 수 있는 제품을 사고 팔 수 있도록 하는 기술 프레임워크를 제공하는 약 1만개의 IEC 국제표준을 발행하고 있다.이러한 ISO와 IEC가 공동으로 구성한 기술위원회 ISO/IEC JTC 1 정보 기술(Information technology)에 대해 살펴볼 예정이다. JTC 1은 1987년에 결성됐으며 사무국은 미국국립표준협회(American National Standards Institute, ANSI)에서 맡고 있다. 위원회는 리사 라지첼(Mrs Lisa Rajchel)가 책임지고 있다. 현재 의장은 필 웬블롬(Mr Phil Wennblom)으로 임기는 202년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), 스티븐 더트널(Mr Stephen Dutnall), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등으로 조사됐다. 범위는 정보기술 분야의 표준화다.현재 ISO/IEC JTC 1의 직접적인 책임 하에 발행된 표준은 517개며 직접적인 책임 하에 개발중인 표준은 23개다. 참여하고 있는 회원은 40개국, 참관 회원은 62개국이다.공동 기술위원회(Joint Technical Committee, JTC) 산하에서 활동하고 있는 분과위원회(Subcommittee, SC) 중 SC 1, SC 2에 이어 SC 6에 대해 살펴보면 다음과 같다.ISO/IEC JTC 1/SC 6 시스템간 통신 및 정보 교환(Telecommunications and information exchange between systems)과 관련된 분과위원회는 1988년 결성됐다. 사무국은 한국 국가기술표준원(Korean Agency for Technology and Standards, KATS)에서 맡고 있다.위원회는 오정엽(Mr Jungyup OH)이 책임지고 있다. 현재 의장은 강현국(Dr Hyun Kook Kahng)으로 임기는 2024년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등으로 조사됐다.범위는 사용 조건 뿐 아니라 시스템 기능, 절차, 매개변수를 포함해 개방형 시스템 간의 정보 교환을 다루는 통신 분야 표준화 작업을 진행해 왔다.이 표준화는 물리적, 데이터 링크, 네트워크 및 전송을 포함한 하위 계층의 프로토콜과 서비스뿐만 아니라 디렉토리 및 ASN.1(MFAN, NFC, PLC, 미래 네트워크 및 OID)을 포함하되 이에 국한되지 않는 상위 계층의 프로토콜 및 서비스를 포함하고 있다.현재 ISO/IEC JTC 1/SC 6 사무국의 직접적인 책임 하에 발행된 표준은 397개며 개발 중인 표준은 18개다. 참여하고 있는 회원은 19명, 참관 회원은 36명이다.□ ISO/IEC JTC 1/SC 6 사무국의 직접적인 책임하에 발행된 표준 및(또는) 프로젝트 397개 중 15개 목록▷ISO 1155:1978 Information processing — Use of longitudinal parity to detect errors in information messages▷ISO 1177:1985 Information processing — Character structure for start/stop and synchronous character oriented transmission▷ISO 1745:1975 Information processing — Basic mode control procedures for data communication systems▷ISO 2110:1989 Information technology — Data communication — 25-pole DTE/DCE interface connector and contact number assignments▷ISO 2110:1989/Amd 1:1991 Information technology — Data communication — 25-pole DTE/DCE interface connector and contact number assignments — Amendment 1: Interface connector and contact number assignments for a DTE/DCE interface for data signalling rates above 20 000 bit/s per second▷ISO/IEC 2593:2000 Information technology — Telecommunications and information exchange between systems — 34-pole DTE/DCE interface connector mateability dimensions and contact number assignments▷ISO 2628:1973 Basic mode control procedures — Complements▷ISO 2629:1973 Basic mode control procedures — Conversational information message transfer▷ISO/IEC 4005-1:2023 Telecommunications and information exchange between systems — Unmanned aircraft area network (UAAN) — Part 1: Communication model and requirements▷ISO/IEC 4005-2:2023 Telecommunications and information exchange between systems — Unmanned aircraft area network (UAAN) — Part 2: Physical and data link protocols for shared communication▷ISO/IEC 4005-3:2023 Telecommunications and information exchange between systems — Unmanned aircraft area network (UAAN) — Part 3: Physical and data link protocols for control communication▷ISO/IEC 4005-4:2023 Telecommunications and information exchange between systems — Unmanned aircraft area network (UAAN) — Part 4: Physical and data link protocols for video communication▷ISO 4902:1989 Information technology — Data communication — 37-pole DTE/DCE interface connector and contact number assignments▷ISO 4903:1989 Information technology — Data communication — 15-pole DTE/DCE interface connector and contact number assignments▷ISO/IEC 5021-1:2023 Telecommunications and information exchange between systems — Wireless LAN access control — Part 1: Networking architecture▷ISO/IEC 5021-2:2023 Telecommunications and information exchange between systems — Wireless LAN access control — Part 2: Dispatching platform□ ISO/IEC JTC 1/SC 6 사무국의 직접적인 책임하에 개발중인 표준 및(또는) 프로젝트 18개 중 15개 목록▷ISO/IEC PRF 4396-1 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 1: Reference model▷ISO/IEC PRF 4396-2 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 2: Common application connection establishment protocol▷ISO/IEC PRF 4396-3 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 3: Common distributed application protocol▷ISO/IEC PRF 4396-4 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 4: Complete enrolment procedures▷ISO/IEC PRF 4396-5 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 5: Incremental enrolment procedures▷ISO/IEC PRF 4396-6 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 6: RINA data transfer service▷ISO/IEC PRF 4396-7 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 7: Flow allocator▷ISO/IEC PRF 4396-8 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 8: RINA general delimiting procedures▷ISO/IEC PRF 4396-9 Telecommunications and information exchange between systems — Recursive inter-network architecture — Part 9: Error and flow control protocol▷ISO/IEC/IEEE DIS 8802-1Q Telecommunications and exchange between information technology systems — Requirements for local and metropolitan area networks — Part 1Q: Bridges and bridged networks▷ISO/IEC 9594-8:2020/CD Cor 2 Information technology — Open systems interconnection — Part 8: The Directory: Public-key and attribute certificate frameworks — Technical Corrigendum 2▷ISO/IEC 9594-11:2020/CD Cor 1 Information technology — Open systems interconnection directory — Part 11: Protocol specifications for secure operations — Technical Corrigendum 1▷ISO/IEC 9594-11:2020/DAmd 1 Information technology — Open systems interconnection directory — Part 11: Protocol specifications for secure operations — Amendment 1▷ISO/IEC DIS 9594-12 Information technology — Open systems interconnection — Part 12: The Directory: Key management and public-key infrastructure establishment and maintenance▷ISO/IEC FDIS 18092 Telecommunications and information exchange between systems — Near Field Communication Interface and Protocol 1 (NFCIP-1)
-
[특집-공동기술위원회] ④JTC 1/SC 2 코드화된 문자 세트(Coded character sets)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(Working Group, WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등을 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.또한 국제전기기술위원회(International Electro-technical Commission, IEC)는 전기 및 전자 제품의 고품질 인프라와 국제 무역을 뒷받침하는 글로벌 비영리 회원 조직이다.기술 혁신, 저렴한 인프라 개발, 효율적이고 지속 가능한 에너지 접근, 스마트 도시화 및 교통 시스템, 기후 변화 완화를 촉진하고 사람과 환경의 안전을 향상시키는 역할을 수행하고 있다. 170개 이상의 국가를 통합하고 전 세계 2만명의 전문가에게 글로벌하고 중립적이며 독립적인 표준화 플랫폼을 제공하고 있다. 장치, 시스템, 설치, 서비스 및 인력이 필요에 따라 작동함을 구성원이 인증하는 4가지 적합성 평가 시스템을 관리한다.적합성 평가와 함께 정부가 국가 품질 인프라를 구축하고 모든 규모의 기업이 전 세계 대부분의 국가에서 일관되게 안전하고 신뢰할 수 있는 제품을 사고 팔 수 있도록 하는 기술 프레임워크를 제공하는 약 1만개의 IEC 국제표준을 발행하고 있다.이러한 ISO와 IEC가 공동으로 구성한 기술위원회 ISO/IEC JTC 1 정보 기술(Information technology)에 대해 살펴볼 예정이다. JTC 1은 1987년에 결성됐으며 사무국은 미국국립표준협회(American National Standards Institute, ANSI)에서 맡고 있다. 위원회는 리사 라지첼(Mrs Lisa Rajchel)가 책임지고 있다. 현재 의장은 필 웬블롬(Mr Phil Wennblom)으로 임기는 202년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), 스티븐 더트널(Mr Stephen Dutnall), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등으로 조사됐다. 범위는 정보기술 분야의 표준화다.현재 ISO/IEC JTC 1의 직접적인 책임 하에 발행된 표준은 517개며 직접적인 책임 하에 개발중인 표준은 23개다. 참여하고 있는 회원은 40개국, 참관 회원은 62개국이다.공동 기술위원회(Joint Technical Committee, JTC) 산하에서 활동하고 있는 분과위원회(Subcommittee, SC) 중 첫 번째 SC 1 활동에 이어 SC 2에 대해 살펴보면 다음과 같다.ISO/IEC JTC 1/SC 2 코드화된 문자 세트(Coded character sets)와 관련된 분과위원회는 1987년 결성됐다. 사무국은 일본산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 나가사와 아유코(Ms Ayuko Nagasawa)가 책임지고 있다. 현재 의장은 마사루 타케치(Mr Masaru Takechi)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 스테판 소바쥬(M Stéphane Sauvage), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등으로 조사됐다.범위는 문자열 순서, 관련 제어 기능, 정보 교환을 위한 코드화된 표현 및 코드 확장 기술을 포함해 그래픽 문자 집합 및 특성의 표준화다. 단, 오디오 및 사진 코딩은 제외된다.현재 ISO/IEC JTC 1/SC 2 사무국의 직접적인 책임하에 발행된 표준은 49개며 개발 중인 표준은 3개다. 참여하고 있는 회원은 24명, 참관 회원은 26명이다.□ ISO/IEC JTC 1/SC 2 사무국의 직접적인 책임하에 발행된 표준 및(또는) 프로젝트 49개 중 15개 목록▷ISO/IEC 646:1991 Information technology — ISO 7-bit coded character set for information interchange▷ISO 962:1974 Information processing — Implementation of the 7- bit coded character set and its 7- bit and 8-bit extensions on 9- track 12,7 mm (0.5 in) magnetic tape▷ISO 1113:1979 Information processing — Representation of the 7- bit coded character set on punched tape▷ISO 1154:1975 Information processing — Punched paper tape — Dimensions and location of feed holes and code holes▷ISO 1681:1973 Information processing — Unpunched paper cards — Specification▷ISO/IEC 2022:1994/Cor 1:1999 Information technology — Character code structure and extension techniques — Technical Corrigendum 1▷ISO/IEC 2022:1994 Information technology — Character code structure and extension techniques▷ISO 2033:1983 Information processing — Coding of machine readable characters (MICR and OCR)▷ISO 2047:1975 Information processing — Graphical representations for the control characters of the 7- bit coded character set▷ISO/IEC 2375:2003 Information technology — Procedure for registration of escape sequences and coded character sets▷ISO 3275:1974 Information processing — Implementation of the 7- bit coded character set and its 7- bit and 8- bit extensions on 3,81 mm magnetic cassette for data interchange▷ISO/IEC 4873:1991 Information technology — ISO 8-bit code for information interchange — Structure and rules for implementation▷ISO 5426-2:1996 Information and documentation — Extension of the Latin alphabet coded character set for bibliographic information interchange — Part 2: Latin characters used in minor European languages and obsolete typograph▷ISO 5426:1983 Extension of the Latin alphabet coded character set for bibliographic information interchange▷ISO 5427:1984 Extension of the Cyrillic alphabet coded character set for bibliographic information interchange□ ISO/IEC JTC 1/SC 2 사무국의 직접적인 책임하에 개발중인 표준 및(또는) 프로젝트 3개 목록▷ISO/IEC CD TR 2375 Information technology – Registered escape sequences and coded character sets▷ISO/IEC 10646:2020/CD Amd 2.3 Information technology — Universal coded character set (UCS) — Amendment 2: Todhri, Garay, Tulu-Tigalari, Sunuwar, Gurung Khema, Kirat Rai, and other characters▷ISO/IEC CD 14651 Information technology — International string ordering and comparison — Method for comparing character strings and description of the common template tailorable ordering
-
한국표준협회, 시스코 클라우드 취업예정자 무료교육 진행IT 인프라 및 클라우드 전문 인력이 양성될 전망이다. 한국표준협회는 시스코코리아, 솔데스크, 한국클라우드산업협회와 함께 디지털 핵심 인재 양성을 위해 솔데스크 종로 본원에서 ‘Cisco VirtuNet Cloud 통합 구현 교육과정’을 개최한다고 5일 밝혔다. 과정은 고용노동부의 ‘2023년 하반기 K-디지털 트레이닝’ 유형의 디지털 선도기업 아카데미 공고를 통해 선정됐다. 참여자는 시스코 네트워킹 아카데미 커리큘럼을 활용한 CCNA, CCNP, Linux 및 AWS 클라우드 등을 960시간 동안 학습하게 된다. 교육은 시스코코리아로부터 인증 받은 강사 직강이며 참여자는 Cisco vXLAN, 가상화기술을 활용한 DataCenter의 네트워크 가상화 및 최적화 구현 프로젝트 등을 수행한다. 수료 시 4개 기관 명의 수료증을 발급하며 6개월 동안 한국클라우드산업협회에서 구인기업 정보 제공 등 IT/SW 업종 내 취업을 지원한다. 총 60명을 선발하며 지원대상은 국민내일배움카드 보유자 및 발급 가능 대상자 중 취업 가능한 미취업자며 국민내일배움카드로 무료 수강할 수 있다. 모집 기간은 4일부터 27일까지며 솔데스크 홈페이지에서 신청할 수 있다. 강명수 회장은 “Cisco VirtuNet Cloud 통합 구현 교육과정을 적극적으로 운영 지원해 IT 인프라 및 클라우드 전문 인력 양성에 이바지하겠다”고 밝혔다.
-
[특집-기술위원회] TC 114 - 시계학(Horology)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111 등이다.ISO/TC 114 시계학(Horology)과 관련된 기술위원회는 TC 112, TC 113과 마찬가지로 1964년 결성됐다. 사무국은 스위스 표준화기구(Swiss Association for Standardization, SNV)에서 맡고 있다.위원회는 패트릭 뢰처(Mr Patrick Lötscher)가 책임지고 있다. 현재 의장은 라파엘 슈바르츠(Mr Raphaël Schwarz)으로 임기는 2027년까지다.ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 빈센조 바주치(M Vincenzo Bazzucchi) 등으로 조사됐다.범위는 시간 측정 및 시간 기록을 위한 소형 및 대형 장비 분야의 표준화다. 또한, 용어, 기술적 정의, 전체 치수의 표준화, 향후 제안될 수 있는 기타 질문 등도 포함된다.현재 ISO/TC 114와 관련해 발행된 표준은 34개며 개발 중인 표준은 1개다. ISO/TC 114 사무국의 직접적인 책임 하에 발행된 표준은 7개다. 참여하고 있는 회원은 10명, 참관 회원은 14명이다.□ ISO/TC 114 사무국의 직접적인 책임 하에 발행된 표준 7개 목록▷ISO 1112:2009 Horology — Functional and non-functional jewels▷ISO 3158:1976 Timekeeping instruments — Symbolization of control positions▷ISO 3159:2009 Timekeeping instruments — Wrist-chronometers with spring balance oscillator▷ISO 12819:2009 Methods of evaluation of the battery life of a battery-powered watch▷ISO 18684:2020 Timekeeping instruments — Watch external parts made of hard material — General requirements and test methods▷IEC 60086-3:2021 Primary batteries — Part 3: Watch batteries▷IEC 60086-3:2021/Cor 1:2023 Primary batteries — Part 3: Watch batteries — Technical Corrigendum 1□ ISO/TC 114 사무국의 소위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 114/SC 1 Shock resistant watches ; 발행된 표준 1개, 개발 중인 표준 0개▷ISO/TC 114/SC 3 Water-resistant watches ; 발행된 표준 2개, 개발 중인 표준 0개▷ISO/TC 114/SC 5 Luminescence ; 발행된 표준 1개, 개발 중인 표준 1개▷ISO/TC 114/SC 6 Precious metal coverings ; 발행된 표준 5개, 개발 중인 표준 0개▷ISO/TC 114/SC 7 Overall dimensions ; 발행된 표준 4개, 개발 중인 표준 0개▷ISO/TC 114/SC 9 Technical definitions ; 발행된 표준 4개, 개발 중인 표준 0개▷ISO/TC 114/SC 11 Indication of accuracy ; 발행된 표준 1개, 개발 중인 표준 0개▷ISO/TC 114/SC 12 Antimagnetism ; 발행된 표준 1개, 개발 중인 표준 0개▷ISO/TC 114/SC 13 Watch-glasses ; 발행된 표준 5개, 개발 중인 표준 0개▷ISO/TC 114/SC 14 Table and wall clocks ; 발행된 표준 3개, 개발 중인 표준 0개
-
[특집-ISO/IEC JTC 1/SC 17 활동] ①Meeting: Singapore (Singapore) 27 Sep 2023지난 9월27일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 싱가포르에서 플레너리 미팅(Plenary meeting, 총)을 개최했다. 플래너리 미팅은 결석자 없이 모든 당사자나 구성원이 참석해 개최되는 회의나 토론회다.참고로 ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안 장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.분과위원회는 이날 개최된 총회와 관련해 'ISO/IEC JTC 1 SC 17 SC17 총회에 대한 WG1 보고서 개정(ISO/IEC JTC 1 SC 17 Revised WG1 Report to SC17 Plenary meeting) 문서를 배포했다.ISO/IEC JTC 1 SC 17 총회와 관련한 워킹그룹(WG1) 컨비너 보고서는 아래 다양한 내용을 포함하고 있다. □ 2023년 3번의 정규 회의 △2023. 2. 벤쿠버 △2023. 6. 줌(Zoom) 회의 △캐나다, 프랑스, 독일, 일본, 뉴질랜드, 영국, 미국 등 전문가 18~22인이 수시로 참석 △2023. 9. 회의 - 원격 참여를 제공하는 첫 번째 오프라인 회의 - 참석자 9명 : 직접 참여 - 참석자 9명 : 온라인 참석 □ 6개 표준 그룹 △물리적 특성 및 시험방법(Physical Characteristics and Test Methods) △엠보싱&TIM(Embossing & TIM) △마그네틱 스트라이프 카드(Magnetic Stripe Cards) △얇고 유연한 카드(Thin Flexible Cards) △카드 서비스 수명(Card Service Life) △ICC 관리 장치(ICC Managed Devices)□ 물리적 특성 및 테스트 방법 △현재 개정 중: - 번호/제목 : 7810, 물리적 특성 - 번호/제목 : 10373-1, 시험방법 제1부: 일반특성 △2020년에 출시된 7810 - 7810에 아직 포함되지 않은 7816-1의 나머지 요구 사항을 포함하는 AMD 1이 FDIS 투표용으로 제출되었음. △2020년에 게시된 10373-1 △10373-1 AMD 1, 박리 강도 방법 사용에 관한 설명 포함, 출판 대기 중□ 엠보싱 - 번호/제목 : 7811-1, 앰보싱 △개정된 7811-1은 2018년에 출판되었으며 안정적임.□ TIM - 번호/제목 : 7811-9, 촉각식별표지(Tactile Identifier Mark, TIM) △개정된 7811-9는 2019년에 출판되었음 △개정 : - 표준 수정/개정을 위해 2건 제안 - 1건은 기여도가 부족해 더 이상 개발할 수 없음. - 1건은 지속적인 반대를 나타냄. - WG1은 개정판을 취소하고 해당 표준을 2015년 형식으로 확정할 것을 요청.□ 마그네틱 스트라이프 카드 - 1(Magnetic Stripe Cards -1) △개정판은 2015년에 개시됐으며 안정적임. - 번호/제목 : 7811-8, 보자력(Coercivity, 자성물질의 저항) 51,7 kA/m (650 Oe) - 번호/제목 : 8484, 예금통장 마그네틱 스트라이프 - 번호/제목 : 10373-2, 시험방법 △2018년에 발표된 7811-2, -6, -7의 개정판이며 안정적임. - 번호/명칭 : 7811-2, LoCo(Low Coercivity) - 번호/명칭 : 7811-6, HiCo(High Coercivity) - 번호/제목 : 7811-7, HiCo(High Coercivity), 고밀도 □ Thin Flexible Cards - 생략 -□ ICC-managed devices - 생략 -□ Laundry Test - 생략 -□ Card Service Life - 생략 -□ Resolutions - 생략 -□ Meeting Policy for 2023 - 생략 -- 이하 생략 -등 다양한 내용이 포함됐다. 표준뉴스는 2023년 9월 싱가포르에서 개최된 SC 17 워킹그롭(WG) 회의 관련 내용을 상세하게 전달할 계획이다. 독자 여러분의 많은 관심과 조언을 부탁드린다.