검색결과
-
[특집] ISO/TC 70 기술위원회(Technical Committees) 소개스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC1 기술위원회를 시작으로 최근 순환경제를 표준화하기 위한 TC323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.ISO/TC 70 내연기관(Internal combustion engines)과 관련된 기술위원회는 1947년 구성된 TC1~TC67, 1948년 구성된 TC 69, 1972년 구성된 TC68과 달리 1949년 만들어졌다.사무국은 중국 국가표준화관리위원회(国家标准化管理委员会, SAC)에서 맡고 있다. 위원회는 웨이빈 지(Mr Weibin Ji)이 책임진다. 의장은 슈링 우(Mr Xuling Wu)으로 임기는 2024년까지다.ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 아룬 ABY 파라에카틸(Mr Arun ABY Paraecattil) 등으로 조사됐다.범위는 엔진과 구동 기계 및 환경 간 관계를 고려한 정의, 성능/테스트 및 특수 요구 사항을 포함해 왕복 및 회전 변위 내연 기관 분야의 표준화다.■ 단, 도로 차량 및 항공기를 추진하는 데 사용되는 왕복 및 회전 변위 엔진은 제외한다.현재 ISO/TC 70 사무국의 직접적인 책임하에 발행된 표준은 49개며 ISO/TC 70 사무국과 관련해 발행된 표준은 74개다.ISO/TC 70 사무국의 직접적인 책임하에 개발 중인 표준은 4개 ISO/TC 70 사무국과 관련해 개발 중인 표준은 7개다. 참여하고 있는 회원은 15명, 참관 회원은 23명이다.□ ISO/TC 70 사무국의 직접적인 책임하에 발행된 표준 15개 목록▲ISO 1204:1990 Reciprocating internal combustion engines — Designation of the direction of rotation and of cylinders and valves in cylinder heads, and definition of right-hand and left-hand in-line engines and locations on an engine▲ISO 2261:1994 Reciprocating internal combustion engines — Hand-operated control devices — Standard direction of motion▲ISO 2710-1:2017 Reciprocating internal combustion engines — Vocabulary — Part 1: Terms for engine design and operation▲ISO 2710-2:2019 Reciprocating internal combustion engines — Vocabulary — Part 2: Terms for engine maintenance▲ISO 3046-1:2002 Reciprocating internal combustion engines — Performance — Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods — Additional requirements for engines for general use▲ISO 3046-3:2006 Reciprocating internal combustion engines — Performance — Part 3: Test measurements▲ISO 3046-4:2009 Reciprocating internal combustion engines — Performance — Part 4: Speed governing▲ISO 3046-5:2001 Reciprocating internal combustion engines — Performance — Part 5: Torsional vibrations▲ISO 3046-6:2020 Reciprocating internal combustion engines — Performance — Part 6: Overspeed protection▲ISO 6798-1:2020 Reciprocating internal combustion engines — Measurement of sound power level using sound pressure — Part 1: Engineering method▲ISO 6798-2:2020 Reciprocating internal combustion engines — Measurement of sound power level using sound pressure — Part 2: Survey method▲ISO 6798-3:2022 Reciprocating internal combustion engines — Measurement of sound power level using sound pressure — Part 3: Survey method for use in situ▲ISO 6826:2022 Reciprocating internal combustion engines — Fire protection▲ISO 7967-1:2005 Reciprocating internal combustion engines — Vocabulary of components and systems — Part 1: Structure and external covers▲ISO 7967-2:2010 Reciprocating internal combustion engines — Vocabulary of components and systems — Part 2: Main running gear□ ISO/TC 70 사무국의 직접적인 책임하게 개발 중인 표준 4개 목록▲ISO/WD 8528-5 Reciprocating internal combustion engine driven alternating current generating sets — Part 5: Generating sets▲ISO/FDIS 8528-6 Reciprocating internal combustion engine driven alternating current generating sets — Part 6: Test methods▲ISO/WD 8528-13 Reciprocating internal combustion engine driven alternating current generating sets — Part 13: Safety▲ISO/WD TS 19425 Reciprocating internal combustion engines — Measurement method for air cleaners — Sound power level of combustion air inlet noise and insertion loss using sound pressure□ ISO/TC 70 사무국의 소위원회(Subcommittee)의 책임하에 발행 및 개발 중인 표준 현황▲ISO/TC 70/SC 7 Tests for lubricating oil filters ; 발행된 표준 14개, 개발 중인 표준 3개▲ISO/TC 70/SC 8 Acceptance sampling ; 발행된 표준 11개, 개발 중인 표준 0개▲ISO/TC 68/SC 6 Measurement methods and results ; 발행된 표준 36개, 개발 중인 표준 5개▲ISO/TC 68/SC 7 Applications of statistical and related techniques for the implementation of Six Sigma ; 발행된 표준 13개, 개발 중인 표준 0개▲ISO/TC 68/SC 8 Exhaust gas emission measurement ; 발행된 표준 10개, 개발 중인 표준 0개
-
[특집] ISO/TC 69 기술위원회(Technical Committees) 소개스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC1 기술위원회를 시작으로 최근 순환경제를 표준화하기 위한 TC323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.ISO/TC 69 통계적 방법의 적용(Applications of statistical methods)과 관련된 기술위원회는 1947년 구성된 TC1~TC67, 1972년 구성된 TC68과 달리 1948년 만들어졌다.사무국은 미국 표준협회(American National Standard Institute, ANSI)에서 맡고 있다. 위원회는 제니퍼 애드무센(Ms Jennifer Admussen)이 책임진다. 의장은 켈리 블랙(Ms Kelly Black)으로 임기는 2027년까지다.ISO 기술 프로그램 관리자는 메르체 페레스 헤르난데스(Mme Mercè Ferrés Hernández), ISO 편집 관리자는 빈센조 바추키(M Vincenzo Bazzucchi) 등으로 조사됐다. 범위는 데이터의 생성 및 수집(계획 및 디자인), 분석, 표시, 해석을 포함한 통계적 방법의 적용 분야 표준화다.■ 주의이사회 결의안 12/1959 및 이사회 결의안 26/1961에 의해 ISO 이사회는 표준화에 통계적 방법을 적용하는 것과 관련된 문제에 모든 ISO 기술 위원회를 위한 자문 역할을 ISO/TC 69에 맡겼다.현재 ISO/TC 69 사무국의 직접적인 책임하에 발행된 표준은 18개며 ISO/TC 69 사무국과 관련해 발행된 표준은 125개다. ISO/TC 69 사무국의 직접적인 책임하에 개발 중인 표준은 1개 ISO/TC 69 사무국과 관련해 개발 중인 표준은 13개다. 참여하고 있는 회원은 20명, 참관 회원은 36명이다.□ ISO/TC 69 사무국의 직접적인 책임하에 발행된 표준 18개 목록▲ISO 2602:1980 Statistical interpretation of test results — Estimation of the mean — Confidence interval▲ISO 2854:1976 Statistical interpretation of data — Techniques of estimation and tests relating to means and variances▲ISO 3301:1975 Statistical interpretation of data — Comparison of two means in the case of paired observations▲ISO 3494:1976 Statistical interpretation of data — Power of tests relating to means and variances▲ISO 3534-1:2006 Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability▲ISO 3534-2:2006 Statistics — Vocabulary and symbols — Part 2: Applied statistics▲ISO 3534-3:2013 Statistics — Vocabulary and symbols — Part 3: Design of experiments▲ISO 3534-4:2014 Statistics — Vocabulary and symbols — Part 4: Survey sampling▲ISO 5479:1997 Statistical interpretation of data — Tests for departure from the normal distribution▲ISO 11453:1996 Statistical interpretation of data — Tests and confidence intervals relating to proportions▲ISO 11453:1996/Cor 1:1999 Statistical interpretation of data — Tests and confidence intervals relating to proportions — Technical Corrigendum 1▲ISO/TR 13519:2012 Guidance on the development and use of ISO statistical publications supported by software▲ISO 16269-4:2010 Statistical interpretation of data — Part 4: Detection and treatment of outliers▲ISO 16269-6:2014 Statistical interpretation of data — Part 6: Determination of statistical tolerance intervals▲ISO 16269-7:2001 Statistical interpretation of data — Part 7: Median — Estimation and confidence intervals▲ISO 16269-8:2004 Statistical interpretation of data — Part 8: Determination of prediction intervals▲ISO/TR 18532:2009 Guidance on the application of statistical methods to quality and to industrial standardization▲ISO 28640:2010 Random variate generation methods□ ISO/TC 69 사무국의 직접적인 책임하게 개발 중인 표준 1개 목록▲ISO/AWI TR 23348 Statistics — Big Data Analytics — Model Validation□ ISO/TC 69 사무국의 소위원회(Subcommittee)의 책임하에 발행 및 개발 중인 표준 현황▲ISO/TC 68/SC 4 Applications of statistical methods in product and process management ; 발행된 표준 21개, 개발 중인 표준 5개▲ISO/TC 68/SC 5 Acceptance sampling ; 발행된 표준 27개, 개발 중인 표준 2개▲ISO/TC 68/SC 6 Measurement methods and results ; 발행된 표준 36개, 개발 중인 표준 5개▲ISO/TC 68/SC 7 Applications of statistical and related techniques for the implementation of Six Sigma ; 발행된 표준 13개, 개발 중인 표준 0개▲ISO/TC 68/SC 8 Application of statistical and related methodology for new technology and product development ; 발행된 표준 10개, 개발 중인 표준 0개
-
[특집] ISO/TC 68 기술위원회(Technical Committees) 소개스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC1 기술위원회를 시작으로 최근 순환경제를 표준화하기 위한 TC323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.ISO/TC 68 금융서비스(Financial services)와 관련된 기술위원회는 1947년 구성된 TC1~TC67과 달리 1972년 만들어졌다.사무국은 미국 표준협회(American National Standard Institute, ANSI)에서 맡고 있다. 위원회는 자넷 시(Ms Janet Busch)가 책임진다. 의장은 짐 노세이(Mr Jim Northey)으로 임기는 2024년까지다.ISO 기술 프로그램 관리자는 샐리 스윙우드(Ms Sally Swingewood), ISO 편집 관리자는 데이비드 리드(Mr David Reid) 등으로 조사됐다. 범위는 은행, 보안, 기타 금융서비스 분야의 표준화다.TC 68(ISO/TC 68)은 금융 서비스 산업의 글로벌 표준을 만드는 일을 담당하고 있다. 또한 자산 관리, 지불, 신용 카드 처리 및 금융 서비스에 특정한 정보 보안 측면을 포함한 코어 뱅킹(core banking), 자본 시장을 다루는 표준을 책임지고 있다. 위원회는 SC2(정보 보안), SC8(참조 데이터) 및 SC9(정보 교환)의 3개 분과로 구성된다. 소위원회, 자문 그룹 및 작업 그룹을 통한 TC 68의 초점은 다음과 같다.▶진화하는 비즈니스 요구 사항, 혁신 및 규제 요구 사항을 지원하기 위한 새로운 표준 개발 식별▶기존 국제 표준의 채택 촉진▶ISO, 기타 표준 및 독점 접근 방식의 공존 관리▶업계 이해관계자의 참여 확인 및 확보 현재 ISO/TC 68 사무국과 관련돼 발행된 표준은 75개며 ISO/TC 68 사무국과 관련해 개발중인 표준은 22개다. 참여하고 있는 회원은 36명, 참관 회원은 49명이다.□ ISO/TC 68 사무국의 소위원회(Subcommittee)의 책임하에 발행 및 개발 중인 표준 현황▲ISO/TC 68/SC 2 Financial Services, security ; 발행된 표준 17개, 개발 중인 표준 8개▲ISO/TC 68/SC 8 Reference data for financial services ; 발행된 표준 21개, 개발 중인 표준 5개▲ISO/TC 68/SC 9 Information exchange for financial services ; 발행된 표준 37개, 개발 중인 표준 9개
-
TTA, 전문인력 양성으로 글로벌 ICT 표준 이끈다한국정보통신기술협회(TTA)가 디지털 혁신 기술 분야 국제표준 선점을 위해 ICT 국제표준화 전문가 양성·지원 사업을 강화한다고 11일 밝혔다. TTA는 정보통신기술(ICT) 표준화 전문기관으로서, 지난 20여 년간 산·학·연 전문가의 표준화 활동 지원을 통해 국제표준화기구(ITU 등 18개)에서 275석의 의장단을 배출하는 등 국제무대에서의 우리나라 주도권 확보에 기여해 왔다. TTA는 2026년까지 ICT 국제표준화 전문가 인력풀을 900명(현재 350명) 규모로 확대하고 의장단 300석 진출을 목표로 표준 전문인력 양성을 단계별로 구분하여 체계적으로 추진할 계획이다. 1단계로는 AI, B5G/6G, 양자통신 등 기술·기구들에 대한 표준화 교육과정을 운영함과 동시에 대학원생들이 국제표준화 전문가로 발돋움할 수 있도록 대학원 표준 전문가 인큐베이팅 랩을 신설하여 지도교수와 함께 국제표준화 활동을 수행하는 대응체계를 지원한다. 2단계는 우리 기술 기반으로 국제표준을 선점하고 국제기구에서 지속적인 주도력 강화를 위해 표준전문가 인력풀을 상시 모집 체계로 개편하여 기술 및 정책 전문가뿐만 아니라 표준 특허 및 전략 전문가, 국제간사 등 지원 대상을 확대한다. 3단계는 국제표준화기구에서 의장단 수임 등 20년 이상 표준화 활동 경력을 보유한 명장급 전문가를 통해 차세대 전문가의 표준화 역량을 강화하고 신규 의장단 양성을 위한 멘토링 서비스를 제공한다. 프로그램은 TTA 홈페이지에서 신청 가능하며 국제표준화 활동에 입문하거나 표준전문가로서 활동 지원을 희망하는 누구나 연중 상시 신청할 수 있다. 최영해 TTA 회장은 “디지털 전환 및 기술패권 경쟁에서 주도권 확보를 위해서는 미래혁신기술 분야에 대한 국제표준화 역량 강화가 무엇보다 중요하다”며 “표준 전문인력 양성 및 전문가 활동 강화를 통해 디지털 강국을 실현하고 국제기구에서 우리나라 전문가들이 표준화 주도권을 확보할 수 있도록 적극 지원하겠다”고 밝혔다.
-
[스라랑카] 표준협회(SLSI), AATCC의 섬유 품질 방법을 국가표준으로 채택스리랑카 표준협회(Sri Lanka Standards Institution, SLSI)에 따르면 AATCC의 섬유 품질 방법을 국가표준으로 채택했다.스리랑카 표준협회(Sri Lanka Standards Institution, SLSI)는 미국 섬유화학자 및 색채전문가 협회(American Association of Textile Chemists and Colorists, AATCC)와 양해각서(memorandum of understanding, MOU)를 체결했다.비영리단체의 섬유제품 품질 방법 및 절차를 스리랑카 국가 표준으로 만들기 위한 목적이다. AATCC 부사장 다이애나 와이먼(Diana Wyman)과 SLSI 사무총장 시디카 G 세나라트네(Siddhika G Senaratne)가 계약서에 서명했다. 이들은 AATCC 및 관련 위원회의 구성원이다.지난 3월 깨끗한 옷 캠페인(Clean Clothes Campaign, 3C)에 따르면 스리랑카 근로자들이 국가의 재정적 어려움을 완화하기 위한 긴급 구호 수당(Emergency Relief Allowances)을 받지 못했다. 지난 1년 동안 스리랑카가 경제위기를 겪었기 때문이다.많은 패션 브랜드업체는 스리랑카의 패션 소싱산업에 대한 지원을 공유하길 원한다. 영국 슈퍼마켓 테스코(Tesco) 역시 스리랑카에서 의류의 소싱을 유지하고 있다.따라서 스리랑카는 섬유산업의 발전을 위해 2020년 콜롬비아 기술 표준 기관 ICONTEC(L'Instituto Colombiano de Normas Técnicas y Certificación)와 유사한 계약을 체결했다.
-
[미국] 바이든 행정부, 핵심 및 신흥 기술(CET)에 대한 국가표준전략(NSS) 발표미국 바이든 행정부(Biden Administration)에 따르면 핵심 및 신흥 기술(Critical and Emerging Technology, CET)에 대한 국가표준전략(National Standards Strategy, NSS)을 발표했다.NSS는 미국 기술이 안전하고 상호운용될 수 있도록 보장하기 위한 지침을 제공한다. NSS는 미국 소비자가 사용하는 기술을 보호하고 글로벌 표준 개발에서 미국의 리더십과 경쟁력을 강화하고 있다.연방정부는 혁신이 효과적인 표준 개발을 촉진하기 때문에 NSS를 통해 산업계와 학계의 관계를 확장하려고 노력하고 있다. 또한 NSS는 파트너들이 표준 개발에 장기적으로 투자하도록 촉구한다.백악관에 따르면 연구와 개발을 통해 생성된 기술발전은 새로운 표준을 뒷받침하는 원동력이다. 정부는 미국을 NSS의 중심에 두기위해 혁신과 최첨단 과학, 중개 연구를 촉진하는 사전 표준화 연구를 지원한다.지난 10년 동안 표준 조직의 수가 빠르게 증가했지만 미국 표준 인력은 보조를 맞추지 못했다. NSS의 선상에서 연방 정부는 다양한 이해관계자들을 교육하고 훈련하는데 투자해 그들이 기술 표준 개발에 더 많이 참여하도록 유도할 계획이다.정부는 동일한 생각을 가진 동맹국과 협력해 국제 표준 시스템에 전 세계의 참여를 유도하고 포용적 성장을 촉진할 공정한 프로세스를 정립할 방침이다.NSS의 목표는 미국 국립표준협회(American National Standards Institute, ANSI)의 미국 표준 전략(United States Standards Strategy)뿐만 아니라 국가 안전보장 전략(National Security Strategy, NSS), 국가 사이버보안 전략(National Cybersecurity Strategy, NCS), 반도체법(CHIPS and Science Act) 등을 포함해 기존의 여러 연방 이니셔티브와 조화를 이루는 것이다.현재 미국 연방정부, 학계, 시민사회 그룹은 글로벌 표준활동에 공헌하고 있다. 정부는 이미 국제 표준 협력 네트워크와 미국-유럽연합(EU) 협력을 통해 파트너 국가와 협력 중이다.
-
[이란] 표준산업연구소(ISIRI), 토양보호를 위한 671개의 표준 설정이란 표준산업연구소(Institute of Standards and Industrial Research of Iran, ISIRI)에 따르면 토양보호를 위한 671개의 표준을 설정했다. 이와 관련된 26개의 다른 표준도 마련했다.환경부(Department of Environment, DoE)에 따르면 토양 관련 표준은 220개, 비료 관련 표준은 89개, 퇴비 관련 표준은 18개, 농약 관련 표준은 322개, 성장 개선제 관련 표준은 19개, 독성 물질 관련 표준은 3개 등으로 총 671개에 달한다.토양오염방지법(Soil Protection Law, SPL)에 따르면 표준산업연구소(ISIRI), 환경부(DoE), 보건부(Ministry of Health, MoH), 농업부(Ministry of Agriculture, MoA)가 공동으로 표준화 작업을 수행해야 한다.이란 국내의 토양 품질은 특별한 주의가 필요하다. 특히 농업 및 천연자원 분야의 비옥한 토양은 파괴와 오염으로부터 보호돼야 하기 때문이다.미래에 식량안보에 문제가 발생생하지 않으려면 토양을 철저하게 관리해야 한다. 침식, 염분과 같은 오염, 파괴로부터 토양을 보호하면 식량안보를 유지할 수 있고 건강한 사회를 만들 수 있기 때문이다.2018년 유엔개발계획(United Nations Development Program, UNDP)에 따르면 전 세계에서 240억 톤(t)의 토양 침식이 발생하고 있다. 이중 이란에서 발생하는 토양침식은 20억 톤으로 전 세계의 약 12분의 1에 해당된다.이란 국토는 세계 육지의 1%로 토양 침식률이 전 세계 평균보다 8배나 높은 셈이다. 심각한 황폐화와 토양 침식으로부터 고통을 받고 있다.정부는 토양 1센티미터를 만들기위해 약 800년이 소요되는 것으로 추정한다. 정부와 국민들은 전 세계 평균의 2배나 많은 관심을 가져야 한다.
-
[특집] ISO/TC 67 기술위원회(Technical Committees) 소개스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC1 기술위원회를 시작으로 최근 순환경제를 표준화하기 위한 TC323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.ISO/TC 67 저탄소에너지를 포함한 석유 및 가스 산업(Oil and gas industries including lower carbon energy)와 관련된 기술위원회는 TC1, TC2, TC4~TC6, TC8, TC10~TC12, TC14, TC17~TC22, TC24~31, TC33~TC39, TC41~TC48, TC51, TC52, TC54, TC58~TC61, TC63과 동일하게 1947년 구성됐다.사무국은 네덜란드표준화기구(Royal Netherlands Standardization Institute, NEN)에서 맡고 있다. 위원회는 프랑수아즈 반 덴 브링크(Mrs Françoise van den Brink)가 책임진다. 의장은 필립 스메들리(Mr Philip Smedley)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 키르시 실란더-반 후넨(Mrs Kirsi Silander-van Hunen), ISO 편집 관리자는 크리스틴 간손레(Ms Christelle Gansonre) 등으로 조사됐다. 범위는 석유화학 및 저탄소 에너지 활동을 포함한 석유 및 가스 산업 분야의 표준화다.□ 제외 사항▲ISO/TC 28에서 다루는 천연 또는 합성 소스의 석유 및 관련 제품, 연료 및 윤활유와 관련된 측면▲ISO/TC 193에서 다루는 천연 가스 관련 측면▲ISO/TC 197에서 다루는 수소 기술과 관련된 측면▲ISO/TC 255에서 다루는 바이오가스 관련 측면▲ISO/TC 265에서 다루는 이산화탄소 포집, 운송 및 지질학적 저장과 관련된 측면▲IMO 요구 사항(ISO/TC 8)이 적용되는 해양 구조물의 측면현재 ISO/TC 67 사무국의 직접적인 책임하에 발행된 표준은 32개며 ISO/TC 67 사무국과 관련해 발행된 표준은 231개다.ISO/TC 67 사무국의 직접적인 책임하에 개발되고 있는 표준은 4개며 ISO/TC 67 사무국과 관련해 개발되고 있는 표준은 44개다. 참여하고 있는 회원은 34명, 참관 회원은 28명이다.□ ISO/TC 67 사무국의 직접적인 책임하에 발행된 표준 32개 중 15개 목록▲ISO/TS 3250:2021 Petroleum, petrochemical and natural gas industries — Calculation and reporting production efficiency in the operating phase▲ISO/TR 12489:2013 Petroleum, petrochemical and natural gas industries — Reliability modelling and calculation of safety systems▲ISO 13085:2014 Petroleum and natural gas industries — Aluminium alloy pipe for use as tubing for wells▲ISO 13879:1999 Petroleum and natural gas industries — Content and drafting of a functional specification▲ISO 13880:1999 Petroleum and natural gas industries — Content and drafting of a technical specification▲ISO/TR 13881:2000 Petroleum and natural gas industries — Classification and conformity assessment of products, processes and services▲ISO 14224:2016 Petroleum, petrochemical and natural gas industries — Collection and exchange of reliability and maintenance data for equipment▲ISO 15156-1:2020 Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 1: General principles for selection of cracking-resistant materials▲ISO 15156-2:2020 Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons▲ISO 15156-3:2020 Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys▲ISO 15546:2011 Petroleum and natural gas industries — Aluminium alloy drill pipe▲ISO 15663:2021 Petroleum, petrochemical and natural gas industries — Life cycle costing▲ISO 16961:2015 Petroleum, petrochemical and natural gas industries — Internal coating and lining of steel storage tanks▲ISO 17348:2016 Petroleum and natural gas industries — Materials selection for high content CO2 for casing, tubing and downhole equipment▲ISO 17349:2016 Petroleum and natural gas industries — Offshore platforms handling streams with high content of CO2 at high pressures□ ISO/TC 67 사무국의 직접적인 책임하에 개발중인 표준 4개 목록▲ISO/DIS 3845 Oil and gas industries including lower carbon energy — Full ring ovalization test method for the evaluation of the cracking resistance of steel line pipe in sour service▲ISO/DIS 16961 Petroleum, petrochemical and natural gas industries — Internal coating and lining of steel storage tanks▲ISO/DIS 24201 Petroleum, petrochemical and natural gas industries — Bulk material for offshore projects — Tertiary outfitting structures▲ISO/FDIS 24202 Oil and gas industries including lower carbon energy — Bulk material for offshore projects — Monorail beam and padeye□ ISO/TC 61 사무국의 소위원회(Subcommittee)의 책임하에 발행 및 개발 중인 표준 현황▲ISO/TC 67/SC 2 Pipeline transportation systems ; 발행된 표준 31개, 개발 중인 표준 18개▲ISO/TC 67/SC 3 Drilling and completion fluids, well cements and treatment fluids ; 발행된 표준 28개, 개발 중인 표준 0개▲ISO/TC 67/SC 4 Drilling, production and injection equipment ; 발행된 표준 55개, 개발 중인 표준 2개▲ISO/TC 67/SC 5 Casing, tubing and drill pipe ; 발행된 표준 12개, 개발 중인 표준 2개▲ISO/TC 67/SC 6 Process equipment, piping, systems, and related safety ; 발행된 표준 34개, 개발 중인 표준 5개▲ISO/TC 67/SC 7 Offshore structures ; 발행된 표준 22개, 개발 중인 표준 11개▲ISO/TC 67/SC 8 Arctic operations ; 발행된 표준 6개, 개발 중인 표준 0개▲ISO/TC 67/SC 9 Production, transport and storage facilities for cryogenic liquefied gases ; 발행된 표준 11개, 개발 중인 표준 2개
-
[특집] ISO/TC 63 기술위원회(Technical Committees) 소개스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC1 기술위원회를 시작으로 최근 순환경제를 표준화하기 위한 TC323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.ISO/TC 63 유리 용기(Glass containers)와 관련된 기술위원회는 TC1, TC2, TC4~TC6, TC8, TC10~TC12, TC14, TC17~TC22, TC24~31, TC33~TC39, TC41~TC48, TC51, TC52, TC54, TC58~TC61과 동일하게 1947년 구성됐다.사무국은 영국표준기구(British Standards Institution, BSI)에서 맡고 있다. 위원회는 크리스토퍼 스타(Mr Christopher Starr)가 책임진다. 의장은 조스퀸 페이세르( M Josquin Peycere)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 스테판 소바쥬(M Stéphane Sauvage), ISO 편집 관리자는 이사벨 베로니카 넬슨(Ms Isabel Veronica Nelson) 등으로 조사됐다. 범위는 포장 수단으로 사용되는 성형 유리로 만든 유리 용기의 표준화다.현재 ISO/TC 63 사무국과 관련해 발행된 표준은 32개며 참여하고 있는 회원은 10명, 참관 회원은 26명이다.□ ISO/TC 63 사무국의 직접적인 책임하에 발행된 표준 32개 중 15개 목록▲ISO 7348:1992 Glass containers — Manufacture — Vocabulary▲ISO 7458:2004 Glass containers — Internal pressure resistance — Test methods▲ISO 7459:2004 Glass containers — Thermal shock resistance and thermal shock endurance — Test methods▲ISO 8106:2004 Glass containers — Determination of capacity by gravimetric method — Test method▲ISO 8113:2004 Glass containers — Resistance to vertical load — Test method▲ISO 9008:1991 Glass bottles — Verticality — Test method▲ISO 9009:1991 Glass containers — Height and non-parallelism of finish with reference to container base — Test methods▲ISO 9057:1991 Glass containers — 28 mm tamper-evident finish for pressurized liquids — Dimensions▲ISO 9057:1991/Cor 1:2006 Glass containers — 28 mm tamper-evident finish for pressurized liquids — Dimensions — Technical Corrigendum 1▲ISO 9058:2008 Glass containers — Standard tolerances for bottles▲ISO 9100-1:2005 Glass containers — Vacuum lug finishes — Part 1: General▲ISO 9100-2:2005 Glass containers — Vacuum lug finishes — Part 2: 33 medium▲ISO 9100-2:2005/Cor 1:2009 Glass containers — Vacuum lug finishes — Part 2: 33 medium — Technical Corrigendum 1▲ISO 9100-3:2005 Glass containers — Vacuum lug finishes — Part 3: 38 regular▲ISO 9100-3:2005/Cor 1:2009 Glass containers — Vacuum lug finishes — Part 3: 38 regular — Technical Corrigendum 1
-
[특집] ISO/TC 60 기술위원회(Technical Committees) 소개스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC1 기술위원회를 시작으로 최근 순환경제를 표준화하기 위한 TC323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.ISO/TC 60 기어(Gears)와 관련된 기술위원회는 TC1, TC2, TC4~TC6, TC8, TC10~TC12, TC14, TC17~TC22, TC24~31, TC33~TC39, TC41~TC48, TC51, TC52, TC54, TC58, TC59와 동일하게 1947년 구성됐다.사무국은 미국표준협회(American National Standards Institute, ANSI)에서 맡고 있다. 위원회는 아미르 아바탈레브(Mr Amir Aboutaleb)가 책임진다. 의장은 테란스 클라베스(Mr Terrance Klaves)으로 임기는 2024년까지다.ISO 기술 프로그램 관리자는 츄안유 쏘우(Ms Chuanyu Zou), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등으로 조사됐다. 범위는 제조 및 제어를 위한 용어, 공칭 치수, 공차 및 도구를 포함한 기어 분야의 표준화다.현재 ISO/TC 60 사무국의 직접적인 책임하에 있는 발행된 표준은 21개며 ISO/TC 60 사무국과 관련해 발행된 표준은 61개다.ISO/TC 60 사무국의 직접적인 책임하에 개발 중인 표준은 3개며 ISO/TC 60 사무국과 관련해 개발 중인 표준은 14개다. 참여하고 있는 회원은 14명, 참관 회원은 21명이다.□ ISO/TC 60 사무국의 직접 책임하에 발행된 표준 21개 중 15개 목록▲ISO 53:1998 Cylindrical gears for general and heavy engineering — Standard basic rack tooth profile▲ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering — Modules▲ISO 677:1976 Straight bevel gears for general engineering and heavy engineering — Basic rack▲ISO 678:1976 Straight bevel gears for general engineering and heavy engineering — Modules and diametral pitches▲ISO 1328-1:2013 Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth▲ISO 1328-2:2020 Cylindrical gears — ISO system of flank tolerance classification — Part 2: Definitions and allowable values of double flank radial composite deviations▲ISO 8579-1:2002 Acceptance code for gear units — Part 1: Test code for airborne sound▲ISO/TR 10064-1:2019 Code of inspection practice — Part 1: Measurement of cylindrical gear tooth flanks▲ISO/TR 10064-2:1996 Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash▲ISO/TR 10064-2:1996/Cor 1:2001 Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash — Technical Corrigendum 1▲ISO/TR 10064-2:1996/Cor 2:2006 Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash — Technical Corrigendum 2▲ISO/TR 10064-3:1996 Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes▲ISO/TR 10064-3:1996/Cor 1:2006 Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes — Technical Corrigendum 1▲ISO/TR 10064-4:1998 Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking▲ISO/TR 10064-4:1998/Cor 1:2006 Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking — Technical Corrigendum 1□ ISO/TC 60 사무국의 직접 책임하에 개발 중인 표준 3개 목록▲ISO/CD TR 10064-2.2 Code of inspection practice — Part 2: Double Flank Radial Composite Measurements▲ISO/CD 21771-2 Cylindrical involute gears and gear pairs — Part 2 — Part 2: Calculation and Measurement of Tooth Thickness and Backlash▲IEC/CD 61400-4 Wind turbines — Part 4: Design requirements for wind turbine gearboxes□ ISO/TC 60 사무국의 소위원회(Subcommittee)의 책임하에 발행 및 개발 중인 표준 현황▲ISO/TC 60/SC 1 Nomenclature and wormgearing ; 발행된 표준 12개, 개발 중인 표준 2개▲ISO/TC 60/SC 2 Gear capacity calculation ; 발행된 표준 28개, 개발 중인 표준 9개