검색결과
-
[특집-기술위원회] TC 198 - 보건 의료 제품의 멸균(Sterilization of health care products)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 등이 있다.ISO/TC 198 보건 의료 제품의 멸균(Sterilization of health care products)과 관련된 기술위원회는 TC 197과 마찬가지로 1990년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 아만다 베네딕(Ms Amanda Benedict)가 책임지고 있다. 현재 의장은 리차드 밴크로프트(Mr Richard Bancroft)이며 임기는 2025년 말까지다.ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje)등이다. 범위는 보건의료 제품의 멸균을 위한 프로세스 및 장비의 표준화다.현재 ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준은 69개며 ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 34개국, 참관 회원은 21개국이다.□ ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준 69개 중 15개 목록▷ISO/TS 5111:2022 Guidance on quality of water for sterilizers, sterilization and washer-disinfectors for health care products▷ISO 11135:2014 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO 11135:2014/Amd 1:2018 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices — Amendment 1: Revision of Annex E, Single batch release▷ISO 11137-1:2006 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices▷ISO 11137-1:2006/Amd 1:2013 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 1▷ISO 11137-1:2006/Amd 2:2018 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 2: Revision to 4.3.4 and 11.2▷ISO 11137-2:2013 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose▷ISO 11137-2:2013/Amd 1:2022 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose — Amendment 1▷ISO 11137-3:2017 Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control▷ISO/TS 11137-4:2020 Sterilization of health care products — Radiation — Part 4: Guidance on process control▷ISO 11138-1:2017 Sterilization of health care products — Biological indicators — Part 1: General requirements▷ISO 11138-2:2017 Sterilization of health care products — Biological indicators — Part 2: Biological indicators for ethylene oxide sterilization processes▷ISO 11138-3:2017 Sterilization of health care products — Biological indicators — Part 3: Biological indicators for moist heat sterilization processes▷ISO 11138-4:2017 Sterilization of health care products — Biological indicators — Part 4: Biological indicators for dry heat sterilization processes▷ISO 11138-5:2017 Sterilization of health care products — Biological indicators — Part 5: Biological indicators for low-temperature steam and formaldehyde sterilization processes□ ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 11135.2 Sterilization of health care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/FDIS 11137-1 Sterilization of health care products — Radiation — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/CD 11140-3 Sterilization of health care products — Chemical indicators — Part 3: Class 2 indicator systems for use in the Bowie and Dick-type steam penetration test▷ISO/CD 11140-4 Sterilization of health care products — Chemical indicators — Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration▷ISO/CD 11140-5 Sterilization of health care products — Chemical indicators — Part 5: Class 2 indicators for Bowie and Dick-type air removal tests▷ISO/AWI 11607-3 Packaging for terminally sterilized medical devices — Part 3: Requirements for process development for forming, sealing and assembly▷ISO/AWI 11737-1 Sterilization of health care products — Microbiological methods — Part 1: Determination of a population of microorganisms on products▷ISO/FDIS 15883-1 Washer-disinfectors — Part 1: General requirements, terms and definitions and tests▷ISO/DIS 15883-2 Washer-disinfectors — Part 2: Requirements and tests for washer-disinfectors employing thermal disinfection for critical and semi-critical medical devices▷ISO/DIS 15883-3 Washer-disinfectors — Part 3: Requirements and tests for washer-disinfectors employing thermal disinfection for human waste containers▷ISO/CD 15883-6 Washer-disinfectors — Part 6: Requirements and tests for washer-disinfectors employing thermal disinfection for noncritical medical devices and health care equipment▷ISO/DIS 15883-7 Washer-disinfectors — Part 7: Requirements and tests for washer-disinfectors employing chemical disinfection for non-critical thermolabile medical devices and health care equipment▷ISO/AWI TS 17664-3 Processing of health care products — Information to be provided by the medical device manufacturer for the processing of medical devices — Part 3: Guidance on the designation of a reusable medical device to a quantitative cleaning classification▷ISO 17665 Sterilization of health care products — Moist heat — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/AWI 19253 Sterilization of health care products — Application of ISO/TS 22421 to the requirements for sterilizers used for the terminal sterilization of health care products containing aqueous liquid in sealed containers
-
[특집-ISO/IEC JTC 1/SC 17 활동] 30. Result of voting on SR Ballot for ISO/IEC 18013-12023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR Ballot for ISO/IEC 18013-1(N 7340)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR Ballot for ISO/IEC 18013-1'는 ISO/IEC 18013-1:2018 (Ed 2)(restricted access)와 관련한 투표결과를 포함하고 있다. ISO/IEC 18013-1:2018 (Ed 2)(restricted access)는 Information technology — Personal identification — ISO-compliant driving licence — Part 1: Physical characteristics and basic data set에 관한 것이다. N 7340 문서는 N 7338, N 7339 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 14개국 △Revise/Amend 1개국 △Abstain lack of national expert input 20개국 등으로 나타났다. - 이하 생략 -
-
[특집-기술위원회] TC 194 - 의료 장비의 생물학적 및 임상적 평가(Biological and clinical evaluation of medical devices)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 등이 있다.ISO/TC 194 의료 장비의 생물학적 및 임상적 평가(Biological and clinical evaluation of medical devices)와 관련된 기술위원회는 TC 192, TC 193과 마찬가지로 1988년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 수잔 민크위츠(Mrs Dr Susann Minkwitz)가 책임지고 있다. 현재 의장은 제레미 팅클러(Mr Jeremy Tinkler)이며 임기는 2026년 말까지다. ISO 기술 프로그램 관리자는 패트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 산잘리 자인(Ms Sanjali Jain)등이다.범위는 해당 장치의 인간 임상 조사에 대한 우수 임상 실습 원칙 뿐 아니라 해당 재료 및 장치에 적용 가능한 생물학적 테스트 방법과 함께 의료 및 치과 재료 및 장치의 생물학적 및 임상 평가에 대한 접근 방식의 표준화다.현재 ISO/TC 194 사무국의 직접적인 책임 하에 발행된 표준은 37개 ISO/TC 194 사무국의 직접적인 책임 하에 개발 중인 표준은 16개다. 참여하고 있는 회원은 33개국, 참관 회원은 19개국이다.□ ISO/TC 194 사무국의 직접적인 책임 하에 발행된 표준 37개 중 15개 목록▷ISO 10993-1:2018 Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk management process▷ISO 10993-2:2022 Biological evaluation of medical devices — Part 2: Animal welfare requirements▷ISO 10993-3:2014 Biological evaluation of medical devices — Part 3: Tests for genotoxicity, carcinogenicity and reproductive toxicity▷ISO 10993-4:2017 Biological evaluation of medical devices — Part 4: Selection of tests for interactions with blood▷ISO 10993-5:2009 Biological evaluation of medical devices — Part 5: Tests for in vitro cytotoxicity▷ISO 10993-6:2016 Biological evaluation of medical devices — Part 6: Tests for local effects after implantation▷ISO 10993-7:2008 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals▷ISO 10993-7:2008/Amd 1:2019 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals — Amendment 1: Applicability of allowable limits for neonates and infants▷ISO 10993-7:2008/Cor 1:2009 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals — Technical Corrigendum 1▷ISO 10993-9:2019 Biological evaluation of medical devices — Part 9: Framework for identification and quantification of potential degradation products▷ISO 10993-10:2021 Biological evaluation of medical devices — Part 10: Tests for skin sensitization▷ISO 10993-11:2017 Biological evaluation of medical devices — Part 11: Tests for systemic toxicity▷ISO 10993-12:2021 Biological evaluation of medical devices — Part 12: Sample preparation and reference materials▷ISO 10993-13:2010 Biological evaluation of medical devices — Part 13: Identification and quantification of degradation products from polymeric medical devices▷ISO 10993-14:2001 Biological evaluation of medical devices — Part 14: Identification and quantification of degradation products from ceramics□ ISO/TC 194 사무국의 직접적인 책임 하에 개발 중인 표준 16개 목록▷ISO/CD 8250 Cleanliness of medical devices — Process design and test methods▷ISO/CD 10993-1.2 Biological evaluation of medical devices — Part 1: Requirements and general principles for the evaluation of biological safety within a risk management process▷ISO/AWI 10993-2 Biological evaluation of medical devices — Part 2: Animal welfare requirements▷ISO/AWI 10993-3 Biological evaluation of medical devices — Part 3: Tests for genotoxicity, carcinogenicity and reproductive toxicity▷ISO 10993-4:2017/DAmd 1 Biological evaluation of medical devices — Part 4: Selection of tests for interactions with blood — Amendment 1▷ISO/CD 10993-6 Biological evaluation of medical devices — Part 6: Tests for local effects after implantation▷ISO/CD 10993-7.2 Biological evaluation of medical devices — Part 7: Ethylene oxide sterilization residuals▷ISO/CD 10993-11 Biological evaluation of medical devices — Part 11: Tests for systemic toxicity▷ISO 10993-12:2021/AWI Amd 1 Biological evaluation of medical devices — Part 12: Sample preparation and reference materials — Amendment 1▷ISO/AWI 10993-16 Biological evaluation of medical devices — Part 16: Toxicokinetic study design for degradation products and leachables▷ISO 10993-17:2023/AWI Amd 1 Biological evaluation of medical devices — Part 17: Toxicological risk assessment of medical device constituents — Amendment 1▷ISO 10993-23:2021/AWI Amd 1 Biological evaluation of medical devices — Part 23: Tests for irritation — Amendment 1▷ISO/CD 14155 Clinical investigation of medical devices for human subjects — Good clinical practice▷ISO/AWI 18969 Clinical evaluation of medical devices▷ISO/AWI 21762 Medical devices utilizing human tissues and their derivatives — Application of risk management▷ISO/AWI TR 24850 Sources of hazard information for medical device constituents
-
[특집-기술위원회] TC 193 - 천연가스(Natural gas)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 등이 있다.ISO/TC 193 천연가스(Natural gas)와 관련된 기술위원회는 TC 192와 마찬가지로 1988년 결성됐다. 사무국은네덜란드 표준화기구(Royal Netherlands Standardization Institute, NEN)에서 맡고 있다.위원회는 니콜렛 바스(Ms Nicolet Baas)이 책임지고 있다. 현재 의장은 아드리안 반 데르 빈(Mr Adriaan van der Veen)이며 임기는 2024년 말까지다. ISO 기술 프로그램 관리자는 키르시 실란데르-반 후넨(Mrs Kirsi Silander-van Hunen), ISO 편집 관리자는 루시 커크(Ms Lucy Kirk)등으로 조사됐다.범위는 아래와 같은 열물리적 특성 계산 및 측정을 포함한 용어, 품질 사양, 측정 방법, 샘플링, 분석 및 테스트 등의 표준화다.- 아래 - ○ 천연 가스○ 천연가스 대체품○ 천연 가스와 가스 연료(예: 비전통 가스 및 재생 가스)의 혼합물 습식 가스○ 생산부터 국경을 넘어 가능한 모든 최종 사용자에게 배송까지 모든 측면○ 액화천연가스(LNG) 분석 방법의 표준화 등도 포함된다. 또한 다른 기술위원회 및 이들 기술위원회와 연계한 천연가스 관련 작업을 인정한다.현재 ISO/TC 193 사무국과 관련해 발행된 표준은 62개며 ISO/TC 193의 직접적인 책임 하에 발행된 표준은 10개다. ISO/TC 193 사무국과 관련해 개발 중인 표준은 19개며 ISO/TC 193의 직접적인 책임 하에 개발 중인 표준은 7개다. 참여하고 있는 회원은 29개국, 참관 회원은 28개국이다.□ ISO/TC 193 사무국의 직접적인 책임 하에 발행된 표준 10개 목록▷ISO 13443:1996 Natural gas — Standard reference conditions▷ISO 13443:1996/Cor 1:1997 Natural gas — Standard reference conditions — Technical Corrigendum 1▷ISO 13686:2013 Natural gas — Quality designation▷ISO 13734:2013 Natural gas — Organic components used as odorants — Requirements and test methods▷ISO 14532:2014 Natural gas — Vocabulary▷ISO 15112:2018 Natural gas — Energy determination▷ISO 15403-1:2006 Natural gas — Natural gas for use as a compressed fuel for vehicles — Part 1: Designation of the quality▷ISO 15970:2008 Natural gas — Measurement of properties — Volumetric properties: density, pressure, temperature and compression factor▷ISO 15971:2008 Natural gas — Measurement of properties — Calorific value and Wobbe index▷ISO/TS 16922:2022 Natural gas — Odorization□ ISO/TC 193 사무국의 직접적인 책임 하에 개발 중인 표준 7개 목록▷ISO/CD TR 5268 Odorants and Odor character▷ISO/AWI 14111 Natural gas — Guidelines to metrological traceability▷ISO/AWI 14532 Natural gas — Vocabulary▷ISO/CD 17507-1 Natural gas — Calculation of methane number of gaseous fuels for reciprocating internal combustion engines — Part 1: MNc method▷ISO/CD 17507-2 Natural gas — Calculation of methane number of gaseous fuels for reciprocating internal combustion engines — Part 2: PKI method▷ISO/DTS 18222.2 Natural gas — Correlation between odorant concentration in air and odour intensity▷ISO/AWI 23219 Natural gas — Format for data from gas chromatograph analysers for natural gas — XML file format□ ISO/TC 193 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 193/SC 1 Analysis of natural gas ; 발행된 표준 46개, 개발 중인 표준 8개▷ISO/TC 193/SC 3 Upstream area ; 발행된 표준 6개, 개발 중인 표준 4개
-
[특집-기술위원회] TC 190 - 토양 품질(Soil quality)… 준설된 수중 토양 물질(굴착된 퇴적물)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186, △1984년 TC 188등이 있다.ISO/TC 190 토양 품질(Soil quality)과 관련된 기술위원회는 TC 189와 마찬가지로 1985년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 테레사 게스바인(Mrs Theresa Geßwein)이 책임지고 있다. 현재 의장은 냇 클라우스 리파르트(Mr Dr. rer. nat Klaus Liphard)이다.ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 발레리아 아가멤논(Ms Valeria Agamennone)등으로 조사됐다.범위는 토양 품질 분야의 표준화다. 원지 토양(원래의 토양), 준설된 수중 토양 물질(굴착된 퇴적물)을 포함해 토양 내 또는 토양 위에서 재사용하기 위한 토양 물질 등도 포함된다.단 토양 품질 평가를 위한 임계값 또는 한계값이나 ISO/TC 182 지질공학에서 다루고 있는 토목공학적 측면이나 ISO/TC 147 수질에서 다루고 있는 현장 퇴적물 등은 제외한다.현재 ISO/TC 190 사무국과 관련해 발행된 표준은 198개며 ISO/TC 190 사무국의 직접적인 책임 하에 발행된 표준은 16개다.ISO/TC 190 사무국과 관련해 개발된 표준은 16개며 ISO/TC 190 사무국의 직접적인 책임 하에 개발 중인 표준은 4개다. 참여하고 있는 회원은 31개국, 참관 회원은 30개국이다.□ ISO/TC 190 사무국의 직접적인 책임 하에 발행된 표준 16개 목록▷ISO 4974:2023 Soil quality — Guidance on soil temperature measurement▷ISO 11074:2015 Soil quality — Vocabulary▷ISO 11074:2015/Amd 1:2020 Soil quality — Vocabulary — Amendment 1▷ISO 11275:2004 Soil quality — Determination of unsaturated hydraulic conductivity and water-retention characteristic — Wind's evaporation method▷ISO 15709:2002 Soil quality — Soil water and the unsaturated zone — Definitions, symbols and theory▷ISO 15903:2002 Soil quality — Format for recording soil and site information▷ISO 16586:2003 Soil quality — Determination of soil water content as a volume fraction on the basis of known dry bulk density — Gravimetric method▷ISO 16586:2003/Cor 1:2009 Soil quality — Determination of soil water content as a volume fraction on the basis of known dry bulk density — Gravimetric method — Technical Corrigendum 1▷ISO 17312:2005 Soil quality — Determination of hydraulic conductivity of saturated porous materials using a rigid-wall permeameter▷ISO 17313:2004 Soil quality — Determination of hydraulic conductivity of saturated porous materials using a flexible wall permeameter▷ISO 20951:2019 Soil Quality — Guidance on methods for measuring greenhouse gases (CO2, N2O, CH4) and ammonia (NH3) fluxes between soils and the atmosphere▷ISO 23400:2021 Guidelines for the determination of organic carbon and nitrogen stocks and their variations in mineral soils at field scale▷ISO 23992:2022 Soil quality — Framework for detailed recording and monitoring of changes in dynamic soil properties▷ISO 25177:2019 Soil quality — Field soil description▷ISO 28258:2013 Soil quality — Digital exchange of soil-related data▷ISO 28258:2013/Amd 1:2019 Soil quality — Digital exchange of soil-related data — Amendment 1□ ISO/TC 190 사무국의 직접적인 책임 하에 개발 중인 표준 4개 목록▷ISO/DIS 11074 Soil quality — Vocabulary▷ISO/CD 18718 Assessment of soil functions and related-ecosystem services: definitions and conceptual Framework▷ISO/CD 18721 Assessment of ecological soil functions: indicators and methods▷ISO/AWI 21251 Guidance for estimating organic carbon stocks in soils according to their biogeochemical stability or or residence time□ ISO/TC 190 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 190/SC 3 Chemical and physical characterization ; 발행된 표준 87개, 개발 중인 표준 13개▷ISO/TC 190/SC 4 Biological characterization ; 발행된 표준 56개, 개발 중인 표준 9개▷ISO/TC 190/SC 7 Impact assessment ; 발행된 표준 39개, 개발 중인 표준 4개
-
TTA, AI 신뢰성 확보와 국제 표준화 적극 추진한다한국정보통신기술협회(TTA)는 1일 인공지능(AI)의 신뢰성을 확보하고 정보통신기술(ICT) 표준화와 소프트웨어(SW) 시험인증 분야의 국제협력을 강화하기 위한 조직개편을 단행했다고 밝혔다. TTA는 “이번 조직개편이 TTA가 우리나라 ICT 분야의 글로벌 표준 및 시험·인증의 선도기관으로서 AI의 신뢰성을 높이기 위한 시험인증 역할을 강화하고, 글로벌 표준개발의 주도적 역할 수행 및 국제협력 강화에 중점을 뒀다”고 설명했다. 먼저 AI융합시험연구소 내 AI신뢰성센터를 신설하여 안전하고 신뢰할 수 있는 AI 활용을 위한 AI 신뢰성 정책연구와 시험인증기관으로서 역할을 강화하고, 국제 표준화를 적극 추진할 예정이다. 표준화본부 내 표준성과센터와 글로벌표준협력센터를 신설해 정부에서 추진하는 정책 및 연구개발을 표준과 연계 강화하고, 우리나라가 주도하는 글로벌 표준협력 프로그램 운영을 통해 주요 표준 선진국 및 신흥국과 양자‧다자 간 표준협력을 강화함으로써 디지털 혁신 기술(인공지능, 데이터, 양자정보통신 등)에 대한 국제 표준화 개발에 주도적 역할을 할 계획이다. 마지막으로 SW시험인증연구소 내 글로벌SW융합인증팀을 신설하여 주요 SW수출국 대상 전문 시험·컨설팅을 통해 우리 SW기업의 글로벌 품질 경쟁력 확보와 해외 수출을 적극 지원할 예정이다. 그동안 TTA는 초거대 AI 기반의 산업 혁신 생태계 조성 지원을 위한 데이터 품질인증기관 자격을 획득하고, AI개발안내서(6종) 및 디지털 기술 표준화 전략 개발·보급, AI 신뢰성 검·인증 서비스와 디지털 혁신기술 분야 국내·외 표준 제·개정 등을 추진했다. 이번 조직개편으로 TTA가 AI와 SW가 일상에 스며든 AX(AI transformation) 시대에 국가 미래 산업 발전에 기여하고, 국내 기업의 글로벌 시장진출을 적극 도울 수 있는 기반을 마련했다. 손승현 TTA 회장은 “안전하고 신뢰할 수 있는 AI 기술 활용과 국제 표준화를 위한 주도적 활동이 그 어느 때보다 중요하다”며 “조직개편을 통해 우리 기업이 국제적 수준의 기술력을 확보하고, 해외시장 진출할 수 있도록 적극 지원하겠다”고 밝혔다.
-
[특집-기술위원회] TC 178 - 리프트·에스컬레이터·무빙워크(Lifts·escalators·moving walks)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 등이 있다.ISO/TC 178 리프트, 에스컬레이터, 무빙워크(Lifts, escalators and moving walks)와 관련된 기술위원회는 TC 176과 마찬가지로 1979년 결성됐다. 사무국은 프랑스 표준화기구(Association Française de Normalization, AFNOR)에서 맡고 있다.위원회는 에바 콘티발(Mme Eva Contival)가 책임지고 있으며 현재 의장은 게로 그슈벤트너(Dr Gero Gschwendtner)다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 리프트, 서비스 리프트, 승객용 컨베이어, 유사 장치 등의 안전을 포함해 모든 사양의 표준화다. 단 지속적인 기계적 취급 장비 및 광산 리프트는 제외한다.현재 ISO/TC 178 사무국의 직접적인 책임 하에 발행된 표준은 43개며 ISO/TC 178 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 31개국, 참관 회원은 27개국이다.□ ISO/TC 178 사무국의 직접적인 책임 하에 발행된 표준 43개 중 15개 목록▷ISO 4190-2:2001 Lift (US: Elevator) installation — Part 2: Class IV lifts▷ISO 4190-3:1982 Passenger lift installations — Part 3: Service lifts class V▷ISO 4190-5:2006 Lift (Elevator) installation — Part 5: Control devices, signals and additional fittings▷ISO 8100-1:2019 Lifts for the transport of persons and goods — Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts▷ISO 8100-2:2019 Lifts for the transport of persons and goods — Part 2: Design rules, calculations, examinations and tests of lift components▷ISO/TS 8100-3:2019 Lifts for the transport of persons and goods — Part 3: Requirements from other Standards (ASME A17.1/CSA B44 and JIS A 4307-1/JIS A 4307-2) not included in ISO 8100-1 or ISO 8100-2▷ISO 8100-20:2018 Lifts for the transport of persons and goods — Part 20: Global essential safety requirements (GESRs)▷ISO/TS 8100-21:2018 Lifts for the transport of persons and goods — Part 21: Global safety parameters (GSPs) meeting the global essential safety requirements (GESRs)▷ISO/TR 8100-24:2016 Safety requirements for lifts (elevators) — Part 24: Convergence of lift requirements▷ISO 8100-30:2019 Lifts for the transport of persons and goods — Part 30: Class I, II, III and VI lifts installation▷ISO 8100-32:2020 Lifts for the transportation of persons and goods — Part 32: Planning and selection of passenger lifts to be installed in office, hotel and residential buildings▷ISO 8100-33:2022 Lifts for the transport of persons and goods — Part 33: T-type guide rails for lift cars and counterweights▷ISO 8100-34:2021 Lifts for the transport of persons and goods — Part 34: Measurement of lift ride quality▷ISO 8102-1:2020 Electrical requirements for lifts, escalators and moving walks — Part 1: Electromagnetic compatibility with regard to emission▷ISO 8102-2:2021 Electrical requirements for lifts, escalators and moving walks — Part 2: Electromagnetic compatibility with regard to immunity□ ISO/TC 178 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 8100-1 Lifts for the transport of persons and goods — Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts▷ISO/DIS 8100-2 Lifts for the transport of persons and goods — Part 2: Design rules, calculations, examinations and tests of lift components▷ISO/AWI 8100-7 Lifts for the transport of persons and goods — Part 7: Accessibility to lifts for persons including persons with disability▷ISO/WD TS 8100-10 Lifts for the transport of persons and goods — Part 10: Building Information Modelling▷ISO/CD TS 8100-22 Lifts for the transport of persons and goods — Part 22: Prerequisites for certification of conformity of lift systems, lift components and lift functions within conformity assessment procedures▷ISO/CD TS 8100-23 Lifts for the transport of persons and goods — Part 23: Certification and accreditation requirements within conformity assessment procedures▷ISO/CD TR 8101-10 Fire safety on lifts — Part 10: Comparison of worldwide safety standards on lifts for firefighters▷ISO/AWI 8102-1 Electrical requirements for lifts, escalators and moving walks — Part 1: Electromagnetic compatibility with regard to emissions▷ISO/AWI 8102-2 Electrical requirements for lifts, escalators and moving walks — Part 2: Electromagnetic compatibility with regard to immunity▷ISO/WD TS 8102-21 Electrical requirements for lifts, escalators and moving walks — Part 21: Part 21: On-site and off-site software updates▷ISO/DIS 8103-1 Escalators and moving walks — Part 1: Safety requirements▷ISO/WD TS 8103-3 Escalators and moving walks — Part 3: Part 3: Requirements from other Standards (ASME A17.1/CSA B44 and JIS codes) not included in ISO▷ISO/AWI 8103-9 Escalators and moving walks — Part 9: Measurement of ride quality▷ISO/DTR 25741-1 Lifts and escalators subject to seismic conditions — Compilation report — Part 1: Rule by rule comparison▷ISO/DTR 25741-2 Lifts and escalators subject to seismic conditions — Compilation report — Part 2: Abbreviated comparison and comments
-
[특집-기술위원회] TC 171 - 문서 관리 어플리케이션(Document management applications)… 캡처·색인화·저장·검색·배포 및 통신·프리젠테이션·마이그레이션스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 등도 포함된다.ISO/TC 171 문서 관리 어플리케이션(Document management applications)과 관련된 기술위원회는 1978년 결성됐다. 사무국은 영국 표준 기구(British Standards Institution, BSI))에서 맡고 있다.위원회는 진 스트라이드(Mrs Jean M Stride)가 책임지고 있으며 현재 의장은 앨런 쉽먼(Mr Alan Shipman)이며 임기는 2026년까지다.ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 이사벨 베로니카 넬슨(Ms Isabel Veronica Nelson) 등으로 조사됐다.범위는 문서 관리 애플리케이션 분야의 캡처, 색인화, 저장, 검색, 배포 및 통신, 프리젠테이션, 마이그레이션, 교환, 보존, 무결성 유지 및 폐기와 관련된 기술 및 프로세스의 표준화다. 문서는 마이크로그래픽 또는 전자형식으로 관리될 수 있다.또한 품질 관리 및 무결성 유지 관리, 문서의 입력/출력 품질(현미경 또는 전자), 지원 메타데이터를 포함해 문서(현미경 또는 전자)의 저장, 사용 및 보존을 위한 구현, 검사 및 품질 관리 절차, 기업 및 인터넷의 작업 흐름(프로세스 관리)과 관련된 애플리케이션, 시스템 간 정보 교환 중 품질 및 무결성 유지, 법적 허용성 및(또는) 무결성 및 보안을 지원하는 절차 및 프로세스, 관련 감사 추적 정보 등도 포함된다.단, TC 46의 범위 내에서 기록 관리 정책 및 절차, TC 184 범위 내에서 산업 자동화 시스템의 정보, 프로세스, 생산 정의 및 작업 흐름에 관한 모든 작업은 제외한다.사진에 적용되는 프로세스, 재료 및 장치의 성능 특성을 테스트, 평가, 분류 및 지정하는 작업을 다룹니다.원본 필름의 촬영, 치수 및 라벨링, ISO/TC 42 범위내 방법 사진에 적용되는 프로세스, 재료 및 장치의 성능 특성을 테스트, 평가, 분류 및 지정하는 작업을 다룹니다.영화 촬영, 원본 필름의 치수 및 라벨링, 사진에 적용할 수 있는 프로세스, 재료 및 장치의 성능 특성을 테스트, 평가, 분류 및 지정하는 ISO/TC 42 범위 내 방법 등도 제외된다.ISO/IEC JTC1의 범위 내에 있는 작업, 특히 ISO/IEC JTC 1/SC 23, SC 24, SC 27, SC 28, SC 29, SC 32 및 SC 34의 작업 역시 제외한다. 참고로 다른 TC와 잠재적 또는 실제 중복이 존재하는 경우 JWG가 적극적으로 추진된다.현재 ISO/TC 171 사무국과 관련해 발행된 표준은 108개 이며 이 중 ISO/TC 171 사무국의 직접적인 책임 하에 발행된 표준은 50개다. ISO/TC 171 사무국과 관련해 개발 중인 표준은 10개다. 참여하고 있는 회원은 16개국, 참관 회원은 31개국이다.□ ISO/TC 171 사무국의 직접적인 책임 하에 발행된 표준 50개 중 15개 목록▷ISO 446:2004 Micrographics — ISO character and ISO test chart No. 1 — Description and use▷ISO 3272-1:2003 Microfilming of technical drawings and other drawing office documents — Part 1: Operating procedures▷ISO 3272-1:2003/Cor 1:2009 Microfilming of technical drawings and other drawing office documents — Part 1: Operating procedures — Technical Corrigendum 1▷ISO 3272-2:1994 Microfilming of technical drawings and other drawing office documents — Part 2: Quality criteria and control of 35 mm silver gelatin microfilms▷ISO 3272-3:2001 Microfilming of technical drawings and other drawing office documents — Part 3: Aperture card for 35 mm microfilm▷ISO 3272-4:1994 Microfilming of technical drawings and other drawing office documents — Part 4: Microfilming of drawings of special and exceptional elongated sizes▷ISO 3272-6:2000 Microfilming of technical drawings and other drawing office documents — Part 6: Quality criteria and control of systems for enlargements from 35 mm microfilm▷ISO 3334:2006 Micrographics — ISO resolution test chart No. 2 — Description and use▷ISO 4087:2005 Micrographics — Microfilming of newspapers for archival purposes on 35 mm microfilm▷ISO 6148:2001 Photography — Micrographic films, spools and cores — Dimensions▷ISO 6196-1:1993 Micrographics — Vocabulary — Part 1: General terms▷ISO 6196-2:1993 Micrographics — Vocabulary — Part 2: Image positions and methods of recording▷ISO 6196-3:1997 Micrographics — Vocabulary — Part 3: Film processing▷ISO 6196-4:1998 Micrographics — Vocabulary — Part 4: Materials and packaging▷ISO 6196-5:1987 Micrographics — Vocabulary — Part 5: Quality of images, legibility, inspection□ ISO/TC 171 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 171/SC 1 Quality, preservation and integrity of information ; 발행된 표준 21개, 개발 중인 표준 3개▷ISO/TC 171/SC 2 Document file formats, EDMS systems and authenticity of information ; 발행된 표준 37개, 개발 중인 표준 7개
-
[특집-기술위원회] TC 165 - 목재 구조물(Timber structures)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.ISO/TC 165 목재 구조물(Timber structures)과 관련된 기술위원회는 1976년 결성됐다. 사무국은 캐나다 표준위원회(Standards Council of Canada, SCC)에서 맡고 있다.위원회는 폴 예를리히(Mr Paul Jaehrlich)가 책임지고 있으며 현재 의장은 잉 추이(Mr Ying Chui)이며 임기는 2024년까지다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 빈센조 바주치(M Vincenzo Bazzucchi) 등으로 조사됐다.범위는 목재, 목재 기반 패널, 기타 목재 기반 제품, 관련 목질계 섬유 재료 등의 구조적 적용에 관한 표준화다. 또한 디자인 요구사항, 재료, 제품, 부품, 구성품의 구조적 특성, 성능 및 설계 값, 관련 구조적, 기계적, 물리적 특성과 성능을 조성하기 위한 테스트 방법 및요구 사항 등도 포함된다.참조 : TC 165의 주제가 구조적이지 않은 목적으로 관련 재료 또는 제품(예 : TC 89 또는 TC 218)의 기술 위원회 주제이기도 한 경우 관련 기술 위원회와 강력한 연락망이 구축된다.현재 ISO/TC 165 사무국의 직접적인 책임 하에 발행된 표준은 54개며 ISO/TC 165 사무국의 직접적인 책임하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 30개국, 참관 회원은 34개국이다.□ ISO/TC 165 사무국의 직접적인 책임 하에 발행된 표준 54개 중 15개 목록▷ISO 5257:2023 Bamboo structures — Engineered bamboo products — Test methods for determination of mechanical properties using small size specimens▷ISO 6891:1983 Timber structures — Joints made with mechanical fasteners — General principles for the determination of strength and deformation characteristics▷ISO 8375:2017 Timber structures — Glued laminated timber — Test methods for determination of physical and mechanical properties▷ISO 8969:2011 Timber structures — Testing of punched metal plate fasteners and joints▷ISO 8970:2020 Timber structures — Testing of joints made with mechanical fasteners — Requirements for timber density▷ISO 9087:1998 Wood - Determination of nail and screw holding power under axial load application▷ISO 9709:2018 Structural timber — Visual strength grading — Basic principles▷ISO 10983:2014 Timber — Finger joints — Minimum production requirements and testing methods▷ISO 10984-1:2009 Timber structures — Dowel-type fasteners — Part 1: Determination of yield moment▷ISO 10984-2:2009 Timber structures — Dowel-type fasteners — Part 2: Determination of embedding strength▷ISO 12122-1:2014 Timber structures — Determination of characteristic values — Part 1: Basic requirements▷ISO 12122-2:2014 Timber structures — Determination of characteristic values — Part 2: Sawn timber▷ISO 12122-3:2016 Timber structures — Determination of characteristic values — Part 3: Glued laminated timber▷ISO 12122-4:2017 Timber structures — Determination of characteristic values — Part 4: Engineered wood products▷ISO 12122-5:2018 Timber structures — Determination of characteristic values — Part 5: Mechanical connections□ ISO/TC 165 사무국의 직접적인 책임 하에 개발중인 표준 3개 목록▷ISO/CD TR 3446 Timber Structures – Determination of characteristic values of sawn timber from tests on Small Clear Wood Specimens▷ISO/DIS 7567 Bamboo structures — Glued laminated bamboo — Product specifications▷ISO/AWI 16229 Timber structures — Laminated strand lumber and oriented strand lumber — Structural properties
-
[기획-디지털 ID 기술] (104)항저우비즈기술(杭州比智科技有限公司), '지능형 멀티-포맷 디지털 아이디 맵핑 방법 및 시스템' 명칭의 중국 특허 등록(CN 116881262)중국 항저우비즈기술(杭州比智科技有限公司)에 따르면 2023년 11월24일 '지능형 멀티-포맷 디지털 아이디 맵핑 방법 및 시스템(Intelligent multi-format digital identity mapping method and system)' 명칭의 중국 특허(CN 116881262)가 등록됐다.본 중국 등록 특허(CN 116881262)는 2023년 9월6일 출원된(CN 2023-11140332) 후 중국 특허청에 의해 심사를 받았다.본 중국 등록 특허(CN 116881262)는 지능형 매핑 기술을 사용해 아이디 정보를 판독 가능 형식으로 변환하고 멀티-메인 바디 데이터 관리를 지원한다.특히 본 중국 등록 특허(CN 116881262)는 디지털 아이디를 보호하고 편리하게 관리하기 위한 지속 가능한 솔루션을 제공한다.본 중국 등록 특허(CN 116881262)의 일 실시예에 따라 데이터 탐색 및 수집, 데이터 전처리, 아이디 맵핑 테이블 생성, 아이디 맵핑 수행, 결과 평가 및 시각화 절차를 포함한다.데이터 탐색 및 수집은 멀티 터미널 멀티 서비스 데이터상에서 실행된다. 각 서비스 데이터베이스별로 데이터에 존재하는 누락, 오류, 중복 항목에 대응하기 위해 데이터 전처리가 실행된다. 비즈니스 데이터베이스의 아이디에 따라 아이디 맵핑 테이블이 생성되고 서로 다른 데이터베이스의 동일한 아이디가 대응된다. 아이디 맵팽 대상이 되는 데이터 파일이 프로그램이나 툴에 로딩된다.아이디 매핑 테이블을 이용하여 매칭 및 변환이 수행된다. 아이디 맵핑 결과에 대한 평가 및 시각화 처리가 수행된다. 표준화와 협력 작업을 통해 다양한 형식의 디지털 아이디가 효율적으로 매핑된다.이를 통해 본 중국 등록 특허(CN 116881262)는 데이터 정확성 및 확장성을 확보하고 다양한 형태의 식별자 및 다수의 데이터베이스를 지원한다.