검색결과
-
[특집-기술위원회] TC 157 - 비체계적 피임약 및 성병(STI) 예방 콘돔(Non-systemic contraceptives and STI barrier prophylactics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 등도 포함된다.ISO/TC 157 비체계적 피임약 및 성병(STI) 예방 콘돔(Non-systemic contraceptives and STI barrier prophylactics)과 관련된 기술위원회는 TC 156과 마찬가지로 1974년 결성됐다. 사무국은 말레이시아 표준부(Department of Standards Malaysia, DSM)에서 맡고 있다.위원회는 페리스 프레데릭(Mr Feris Frederick)이 책임지고 있다. 현재 의장은 파리다 하님 압 하난(Dr Faridah Hanim Ab Hanan)로 임기는 2026년까지다. ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 비체계적 피임약 및 성병(sexually transmitted infections, STI)을 예방하기 위한 콘돔의 표준화다.현재 ISO/TC 157 사무국의 직접적인 책임 하에 발행된 표준은 18개며 ISO/TC 15 사무국의 직접적인 책임 하에 개발중인 표준은 2개다. 참여하고 있는 회원은 24개국, 참관 회원은 28개국이다.□ ISO/TC 157 사무국의 직접적인 책임 하에 발행된 표준 18개 목록▷ISO 4074:2015 Natural rubber latex male condoms — Requirements and test methods▷ISO 7439:2023 Copper-bearing contraceptive intrauterine devices — Requirements and tests▷ISO 8009:2014 Mechanical contraceptives — Reusable natural and silicone rubber contraceptive diaphragms — Requirements and tests▷ISO 11249:2018 Copper-bearing intrauterine contraceptive devices — Guidance on the design, execution, analysis and interpretation of clinical studies▷ISO 16037:2002 Rubber condoms for clinical trials — Measurement of physical properties▷ISO 16037:2002/Amd 1:2011 Rubber condoms for clinical trials — Measurement of physical properties — Amendment 1▷ISO 16038:2017 Male condoms — Guidance on the use of ISO 4074 and ISO 23409 in the quality management of condoms▷ISO 19351:2019 Fallopian rings — Requirements and test methods▷ISO 19671:2018 Additional lubricants for male natural rubber latex condoms — Effect on condom strength▷ISO/TR 19969:2018 Guidance on sample handling for determination of bursting volume and pressure, and testing for freedom from holes for male condom▷ISO 23409:2011 Male condoms — Requirements and test methods for condoms made from synthetic materials▷ISO/TR 24484:2023 Female condoms — Use of ISO 25841 and the quality management of female condoms▷ISO 25841:2017 Female condoms — Requirements and test methods▷ISO 25841:2017/Amd 1:2020 Female condoms — Requirements and test methods — Amendment 1▷ISO 29941:2010 Condoms — Determination of nitrosamines migrating from natural rubber latex condoms □ ISO/TC 157 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록▷ISO/CD 4074 Natural rubber latex male condoms — Requirements and test methods▷ISO/TS 23148 Compatibility of lubricants with synthetic male condoms
-
[특집-기술위원회] TC 156 - 금속 및 합금의 부식(Corrosion of metals and alloys)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 등도 포함된다.ISO/TC 156 금속 및 합금의 부식(Corrosion of metals and alloys)과 관련된 기술위원회는 1974년 결성됐다. 사무국은 중국 국가표준화관리위원회(国家标准化管理委员会, Standardization Administration of the P. R. C, SAC)에서 맡고 있다.위원회는 호우 지에(Mrs Jie Hou)이 책임지고 있다. 현재 의장은 평 챠오(Mr Chao Feng)로 임기는 2025년까지다. ISO 기술 프로그램 관리자는 추 주안우(Ms Chuanyu Zou), ISO 편집 관리자는 엔 기엣(Ms Anne Guiet) 등으로 조사됐다.범위는 부식 테스트 방법, 부식 방지 방법 및 부식 제어 엔지니어링 수명주기를 포함한 금속 및 합금 부식 분야의 표준화다. ISO 내에서 이러한 분야의 활동에 대한 일반적인 조정자 역할도 수행한다.현재 ISO/TC 156 사무국과 관련해 발행된 표준은 118개며 직접적인 책임 하에 발행된 표준은 114개다. ISO/TC 156 사무국과 관련해 개발 중인 표준은 28개며 직접적인 책임하에 개발중인 표준은 26개다. 참여하고 있는 회원은 24개국, 참관 회원은 26개국이다.□ ISO/TC 156 사무국의 직접적인 책임 하에 발행된 표준 114개 중 15개 목록▷ISO 3079:2022 Two-electrode method using acetic acid to measure pitting potential of aluminium and aluminium alloys in chloride solutions▷ISO 3651-1:1998 Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in nitric acid medium by measurement of loss in mass (Huey test)▷ISO 3651-2:1998 Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid▷ISO 3651-3:2017 Determination of resistance to intergranular corrosion of stainless steels — Part 3: Corrosion test for low-Cr ferritic stainless steels▷ISO 4212:2023 Corrosion of metals and alloys — Method of oxalic acid etching test for intergranular corrosion of austenitic stainless steel▷ISO 4215:2022 Corrosion of metals and alloys — Test method for high-temperature corrosion testing of metallic materials by thermogravimetry under isothermal or cyclic conditions▷ISO 4631:2023 Corrosion of metals and alloys — Measurement of the electrochemical critical localized corrosion potential (E-CLCP) for Ti alloys fabricated via additive manufacturing method in simulated biomedical solutions▷ISO 4680:2022 Corrosion of metals and alloys — Uniaxial constant-load test method for evaluating susceptibility of metals and alloys to stress corrosion cracking in high-purity water at high temperatures▷ISO 4905:2023 Corrosion of metals and alloys — Electrochemical test methods for high-temperature corrosion testing of metallic materials in molten salts▷ISO 5156:2022 Corrosion of metals and alloys — Corrosion test method for disinfectant — Total immersion method▷ISO 5668:2023 Corrosion of metals and alloys — Guidelines and requirements for corrosion testing in simulated environment of deep-sea water▷ISO 6509-1:2014 Corrosion of metals and alloys — Determination of dezincification resistance of copper alloys with zinc — Part 1: Test method▷ISO 6509-2:2017 Corrosion of metals and alloys — Determination of dezincification resistance of copper alloys with zinc — Part 2: Assessment criteria▷ISO 7384:1986 Corrosion tests in artificial atmosphere — General requirements▷ISO 7441:2015 Corrosion of metals and alloys — Determination of bimetallic corrosion in atmospheric exposure corrosion tests □ ISO/TC 156 사무국의 직접적인 책임 하에 개발 중인 표준 26개 중 15개 목록▷ISO/DIS 5929 Corrosion of Metals and Alloys — Test and evaluation method for the corrosion of steel bar embedded in concrete structure exposed to total corrosion zones in marine environments▷ISO/DIS 7054 Corrosion of metals and alloys — Wiping method for measurements of gases and particles on real structures and equipment▷ISO 7539-6:2018/DAmd 1 Corrosion of metals and alloys — Stress corrosion testing — Part 6: Preparation and use of precracked specimens for tests under constant load or constant displacement — Amendment 1▷ISO/DIS 8044 Corrosion of metals and alloys — Vocabulary▷ISO 8407:2021/CD Amd 1 Corrosion of metals and alloys — Removal of corrosion products from corrosion test specimens — Amendment 1▷ISO/TR 8547 Corrosion of metals and alloys — Exposure test results in the Asian Monsoon region▷ISO/AWI TR 8564 Corrosion of metals and alloys — Reference data for ISO16539 Method B▷ISO 9227:2022/DAmd 1 Corrosion tests in artificial atmospheres — Salt spray tests — Amendment 1: Footnote of warning▷ISO/CD 9350 Corrosion of Metals and Alloys — Testing method for corrosion resistance for hafnium in the hightemperature and pressure▷ISO/DIS 9351 Galvanic anodes for cathodic protection in seawater and saline sediments▷ISO/DIS 9812 Corrosion of metals and alloys — Corrosion test method for disinfectant — Spray test method▷ISO 10062:2022/DAmd 1 Corrosion tests in artificial atmosphere at very low concentrations of polluting gas(es) — Amendment 1: Footnote of warning▷ISO/CD TR 11303 Corrosion of metals and alloys — Guidelines for selection of protection methods against atmospheric corrosion▷ISO 11782-2:1998/DAmd 1 Corrosion of metals and alloys — Corrosion fatigue testing — Part 2: Crack propagation testing using precracked specimens — Amendment 1▷ISO/AWI 16364 Guidelines for Galvanic Corrosion Control□ ISO/TC 156 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 156/SC 1 Corrosion control engineering life cycle : 발행된 표준 4개, 개발 중인 표준 2개
-
[특집-기술위원회] TC 153 - 밸브(Valves)… 현재까지 28개 표준 발행스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136, △1970년 TC 137, TC 138, TC 142, TC 145 등도 포함된다.ISO/TC 153 밸브(Valves)와 관련된 기술위원회는 TC 146, TC 147, TC 148, TC 149, TC 150과 마찬가지로 1971년 결성됐다. 사무국은 프랑스 표준화기구(Association Française de Normalization, AFNOR)에서 맡고 있다.위원회는 헬렌 크로스(Mme Hélène Cros)가 책임지고 있다. 현재 의장은 파스칼 빈지오(M Pascal Vinzio)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 메르세 페레 에르난데스(Mme Mercè Ferrés Hernández), ISO 편집 관리자는 파비올라 카라골 리베라(Ms Fabiola Caragol Rivera) 등으로 조사됐다.범위는 산업용 밸브, 어태치먼트 포함한 밸브 액츄에이터, 스팀 트랩 분야의 표준화다. 호환성을 다루는 매개변수, 액추에이터 장착을 위한 밸브 결합 세부 사항, 테스트, 마킹, 품질 요구 사항, 용어 및 기타 관련 매개 변수를 포함하고 있다. 단, 아래 사항은 153 표준화에서 제외된다.△ISO / TC 185의 책임인 안전 및 릴리프 밸브 및 기타 압력 릴리프 장치△ISO/TC 67의 책임인 석유 및 천연가스 산업용 크로스 컨트리 파이프라인용 웰헤드 장비용 생산 밸브 및 밸브△IEC / TC 65의 책임을 맡은 산업 공정 제어 시스템에 사용되는 최종 제어 요소를 형성하는 밸브△ISO / TC 138의 책임을 맡은 주로 플라스틱으로 만들어진 외피를 가진 밸브△위생용 밸브△솔레노이드현재 ISO/TC 153 사무국의 직접적인 책임 하에 발행된 표준은 28개며 SO/TC 150 사무국의 직접적인 책임 하에 개발 중인 표준은 2개다. 참여하고 있는 회원은 20개국, 참관 회원은 25개국이다.□ ISO/TC 153 사무국의 직접적인 책임 하에 발행된 표준 28개 중 15개 목록▷ISO 5115:2023 Industrial valves — Part-turn valve actuation▷ISO 5117:2023 Automatic steam traps — Production and performance characteristic tests▷ISO 5208:2015 Industrial valves — Pressure testing of metallic valves▷ISO 5209:2019 General purpose industrial valves — Marking▷ISO 5210:2023 Industrial valves — Multi-turn valve actuator attachments▷ISO 5211:2023 Industrial valves — Part-turn actuator attachments▷ISO 5752:2021 Metal valves for use in flanged pipe systems — Face-to-face and centre-to-face dimensions▷ISO 6002:2021 Industrial valves — Bolted bonnet steel gate valves▷ISO 6552:1980 Automatic steam traps — Definition of technical terms▷ISO 6552:1980/Cor 1:2009 Automatic steam traps — Definition of technical terms — Technical Corrigendum 1▷ISO 6553:2016 Automatic steam traps — Marking▷ISO 6554:1980 Flanged automatic steam traps — Face-to-face dimensions▷ISO 6704:1982 Automatic steam traps — Classification▷ISO 7121:2016 Steel ball valves for general-purpose industrial applications▷ISO 10434:2020 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries □ ISO/TC 153 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록 ▷ISO 5640 Industrial valves — Mounting kits for part-turn valve actuator attachment ▷ISO/CD 12101 Industrial valves — Measurement, test and qualification procedures for fugitive emissions — Classification system and qualification procedures for type testing of stem seals for valves
-
[특집-기술위원회] TC 150 - 수술용 임플란트(Implants for surgery)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136, △1970년 TC 137, TC 138, TC 142, TC 145 등도 포함된다.ISO/TC 150 수술용 임플란트(Implants for surgery)와 관련된 기술위원회는 TC 146, TC 147, TC 148, TC 149과 마찬가지로 1971년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 클라우스 자이어(Mr Klaus Zeier)가 책임지고 있다. 현재 의장은 하니 데미안(Mr Hany Demian)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 산잘리 자인(Ms Sanjali Jain) 등으로 조사됐다.범위는 수술용 임플란트 분야의 표준화다. 또한 수술용 임플란트에 필요한 장비의 표준화뿐아니라 모든 유형의 임플란트, 제조 및 적용에 사용되는 기본 및 복합 재료에 대한 용어, 사양, 테스트 방법을 다루고 있다.수술용 임플란트는 진단 또는 치료 목적으로 일시적 또는 영구적으로 신체에 외과적으로 이식되는 물체 또는 장치를 말한다.현재 ISO/TC 150 사무국과 관련해 발행된 표준은 170개며 이 중 사무국의 직접적인 책임 하에 발행된 표준은 17개다. SO/TC 150 사무국과 관련해 개발중인 표준은 51개며 이 중 직접적인 책임 하에 개발 중인 표준은 4개다. 참여하고 있는 회원은 24개국, 참관 회원은 22개국이다.□ ISO/TC 150 사무국의 직접적인 책임 하에 발행된 표준 17개 목록▷ISO 7197:2006 Neurosurgical implants — Sterile, single-use hydrocephalus shunts and components▷ISO 7197:2006/Cor 1:2007 Neurosurgical implants — Sterile, single-use hydrocephalus shunts and components — Technical Corrigendum 1▷ISO 9713:2022 Neurosurgical implants — Self-closing intracranial aneurysm clips▷ISO 12891-1:2015 Retrieval and analysis of surgical implants — Part 1: Retrieval and handling▷ISO 12891-2:2020 Retrieval and analysis of surgical implants — Part 2: Analysis of retrieved surgical implants▷ISO 13179-1:2021 Implants for surgery — Coatings on metallic surgical implants — Part 1: Plasma-sprayed coatings derived from titanium or titanium-6 aluminum-4 vanadium alloy powders▷ISO/TR 14283:2018 Implants for surgery — Essential principles of safety and performance▷ISO 14607:2018 Non-active surgical implants — Mammary implants — Particular requirements▷ISO 14630:2012 Non-active surgical implants — General requirements▷ISO 16054:2019 Implants for surgery — Minimum data sets for surgical implants▷ISO 16061:2021 Instruments for use in association with non-active surgical implants — General requirements▷ISO 17327-1:2018 Non-active surgical implants — Implant coating — Part 1: General requirements▷ISO/TR 17327-2:2021 Non-active surgical implants — Implant coating — Part 2: Reference standards related to coatings▷ISO 19213:2017 Implants for surgery — Test methods of material for use as a cortical bone model▷ISO 19227:2018 Implants for surgery — Cleanliness of orthopedic implants — General requirements▷ISO/TS 20721:2020 Implants for surgery — General guidelines and requirements for assessment of absorbable metallic implants▷ISO 22926:2023 Implants for surgery — Specification and verification of synthetic anatomical bone models for testing □ ISO/TC 150 사무국의 직접적인 책임 하에 개발 중인 표준 4개 목록▷ISO/CD 5092 Additive manufacturing for medical — General principles — Additive manufacturing of non-active implants ▷ISO/DIS 7197 Neurosurgical implants — Sterile, single-use hydrocephalus shunts▷ISO/DIS 14607 Non-active surgical implants — Mammary implants — Specific requirements▷ISO/FDIS 14630 Non-active surgical implants — General requirements□ ISO/TC 150 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 150/SC 1 Materials ; 발행된 표준 38개, 개발 중인 표준 13개▷ISO/TC 150/SC 2 Cardiovascular implants and extracorporeal systems ; 발행된 표준 37개, 개발 중인 표준 15개▷ISO/TC 150/SC 4 Bone and joint replacements ; 발행된 표준 36개, 개발 중인 표준 12개▷ISO/TC 150/SC 5 Osteosynthesis and spinal devices ; 발행된 표준 26개, 개발 중인 표준 1개▷ISO/TC 150/SC 6 Active implants ; 발행된 표준 16개, 개발 중인 표준 4개▷ISO/TC 150/SC 7 Tissue-engineered medical products ; 발행된 표준 5개, 개발 중인 표준 2개
-
[특집-기술위원회] TC 142 - 공기 및 기타 가스 청소 장비(Cleaning equipment for air and other gases)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다. 기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136 등도 포함된다.ISO/TC 142 공기 및 기타 가스 청소 장비(Cleaning equipment for air and other gases) 관련된 기술위원회는 TC 137, TC 138과 마찬가지로 1970년 결성됐다. 사무국은 이탈리아 표준화기구(Ente Italiano di Normazione, UNI)에서 맡고 있다.위원회는 안나 마르티노(Mrs Anna Martino)가 책임지고 있다. 현재 의장은 리카르도 로마노(Mr Riccardo Romanò)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등으로 조사됐다.범위는 일반 환기 및 산업용 응용 분야의 공기 및 가스 청소, 소독 장비에 대한 용어, 분류, 특성, 테스트 및 성능 방법 분야의 표준화다.단, 다른 ISO 기술 위원회의 범위 내에 있는 모바일 장비의 가스 터빈 및 IC 엔진용 배기 가스 세정기는 제외한다. 또한 기술 위원회 ISO/TC 94 업무 분야인 개인 보호 장비용 필터, ISO/TC 22, 23 및 127이 적용되는 모바일 장비의 캐빈 필터 등도 표준화 범위에서 제외된다.현재 ISO/TC 142 사무국의 직접적인 책임 하에 발행된 표준은 27개며 ISO/TC 142 사무국의 직접적인 책임 하에 개발 중인 표준은 22개다. 참여하고 있는 회원은 23개국, 참관 회원은 20개국이다.□ ISO/TC 142 사무국의 직접적인 책임 하에 발행된 표준 27개 중 15개 목록▷ISO 10121-1:2014 Test method for assessing the performance of gas-phase air cleaning media and devices for general ventilation — Part 1: Gas-phase air cleaning media▷ISO 10121-2:2013 Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation — Part 2: Gas-phase air cleaning devices (GPACD)▷ISO 10121-3:2022 Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation — Part 3: Classification system for GPACDs applied to treatment of outdoor air▷ISO 15714:2019 Method of evaluating the UV dose to airborne microorganisms transiting in-duct ultraviolet germicidal irradiation devices▷ISO 15727:2020 UV-C devices — Measurement of the output of a UV-C lamp▷ISO 15858:2016 UV-C Devices — Safety information — Permissible human exposure▷ISO 15957:2015 Test dusts for evaluating air cleaning equipment▷ISO 16170:2016 In situ test methods for high efficiency filter systems in industrial facilities▷ISO 16890-1:2016 Air filters for general ventilation — Part 1: Technical specifications, requirements and classification system based upon particulate matter efficiency (ePM)▷ISO 16890-2:2022 Air filters for general ventilation — Part 2: Measurement of fractional efficiency and air flow resistance▷ISO 16890-3:2016 Air filters for general ventilation — Part 3: Determination of the gravimetric efficiency and the air flow resistance versus the mass of test dust captured▷ISO 16890-4:2022 Air filters for general ventilation — Part 4: Conditioning method to determine the minimum fractional test efficiency▷ISO 16891:2016 Test methods for evaluating degradation of characteristics of cleanable filter media▷ISO 21083-1:2018 Test method to measure the efficiency of air filtration media against spherical nanomaterials — Part 1: Size range from 20 nm to 500 nm▷ISO/TS 21083-2:2019 Test method to measure the efficiency of air filtration media against spherical nanomaterials — Part 2: Size range from 3 nm to 30 nm□ ISO/TC 114 사무국의 직접적인 책임 하에 개발 중인 표준 22개 중 15개 목록▷ISO/CD 5371 High efficiency filtration units in exhaust ventilation system of biosafety facilities▷ISO/AWI 10121-1 Test method for assessing the performance of gas-phase air cleaning media and devices for general ventilation — Part 1: Gas-phase air cleaning media▷ISO/AWI 10121-2 Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation — Part 2: Gas-phase air cleaning devices (GPACD)▷ISO/CD 15858 UV-C Devices — Safety information — Permissible human exposure▷ISO/AWI 15957 Test dusts for evaluating air cleaning equipment▷ISO/DIS 16313-1 Laboratory test of dust collection systems utilizing porous filter media online cleaned using pulses of compressed gas — Part 1: Systems utilizing integrated fans▷ISO/AWI 16890-1 Air filters for general ventilation — Part 1: Technical specifications, requirements and classification system based upon particulate matter efficiency (ePM)▷ISO/DIS 16890-3 Air filters for general ventilation — Part 3: Determination of the gravimetric efficiency and the air flow resistance versus the mass of test dust captured▷ISO/AWI 17597 Test Method for Measuring in-duct AirborneMicroorganisms Inactivation Effectiveness (AMIE)▷ISO/FDIS 23137-1 Requirements for aerosol filters used in nuclear facilities against specified severe conditions — Part 1: General requirements▷ISO/DIS 23138 Biological equipment for treating air and other gases — Principles and classification▷ISO/DIS 23742 Test method for the evaluation of permeability and filtration efficiency distribution of bag filter medium▷ISO/FDIS 29461-3 Air intake filter systems for rotary machinery — Test methods — Part 3: Mechanical integrity of filter elements▷ISO/CD 29461-4 Air intake filter systems for rotary machinery — Part 4: Test methods for static filter systems in coastal and offshore environments▷ISO/DIS 29463-1 High efficiency filters and filter media for removing particles from air — Part 1: Classification, performance, testing and marking
-
[특집-기술위원회] TC 138 - 유체 수송용 플라스틱 파이프, 피팅 및 밸브(Plastics pipes, fittings and valves for the transport of fluids)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다. 기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136 등도 포함된다.ISO/TC 138 신발 사이즈 지정 및 표시 시스템(Footwear sizing designations and marking systems)과 관련된 기술위원회는 TC 137과 마찬가지로 1970년 결성됐다. 사무국은 일본산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 카마타 히로시(Mr Hiroshi Kamata)가 책임지고 있다. 현재 의장은 쿠리타 토루(Mr Toru Kurita)으로 임기는 2026년까지다.ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등으로 조사됐다.범위는 모든 유형의 강화 플라스틱을 포함해 모든 유형의 플라스틱 재료로 제작되고 유체 운송용으로 제작된 파이프, 피팅, 밸브 및 보조 장비의 표준화다. 또한 플라스틱 파이프에 사용되는 금속 부품의 표준화도 포함되어 있다.이 표준화에는 파이프, 플랜지, 피팅, 밸브 및 보조 장비의 경우 치수 및 공차가 포함된다. 화학적, 기계적, 물리적 특성, 적절한 테스트 방법에 대한 요구사항, 특정 응용 분야와 관련된 기타 특성에 대한 요구 사항, 테스트 방법 온도 및 압력 등급 등에 관한 표준화도 포함된다.현재 ISO/TC 138 사무국과 관련해 발행된 표준은 355개며 ISO/TC 138 사무국의 직접적인 책임 하에 발행된 표준은 7개다. ISO/TC 138 사무국과 관련해 개발중인 표준은 41개며 참여하고 있는 회원은 41개국, 참관 회원은 35개국이다.□ ISO/TC 138 사무국의 직접적인 책임 하에 발행된 표준 7개 목록▷ISO 161-1:2018 Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series▷ISO 161-1:2018/Amd 1:2023 Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series — Amendment 1▷ISO 161-2:1996 Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 2: Inch-based series▷ISO 4065:2018 Thermoplastics pipes — Universal wall thickness table▷ISO 11922-1:2018 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series▷ISO 11922-2:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 2: Inch-based series▷ISO 13966:1998 Thermoplastics pipes and fittings — Nominal ring stiffnesses□ ISO/TC 138 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 138/SC 1 Acoustic emission testing ; 발행된 표준 38개, 개발 중인 표준 2개▷ISO/TC 138/SC 2 Surface methods ; 발행된 표준 89개, 개발 중인 표준 8개▷ISO/TC 138/SC 3 Ultrasonic testing ; 발행된 표준 14개, 개발 중인 표준 4개▷ISO/TC 138/SC 4 Eddy current testing ; 발행된 표준 36개, 개발 중인 표준 8개▷ISO/TC 138/SC 5 Radiographic testing ; 발행된 표준 100개, 개발 중인 표준 10개▷ISO/TC 138/SC 6 Leak testing ; 발행된 표준 29개, 개발 중인 표준 4개▷ISO/TC 138/SC 7 Personnel qualification ; 발행된 표준 18개, 개발 중인 표준 3개▷ISO/TC 138/SC 8 Thermographic testing ; 발행된 표준 24개, 개발 중인 표준 2개
-
[특집-기술위원회] TC 135 - 비파괴 검사(Non-destructive testing)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127 등도 포함된다.ISO/TC 135 비파괴 검사(Non-destructive testing)와 관련된 기술위원회는 TC 130, TC 131, TC 132, TC 133, TC 134와 마찬가지로 1969년 결성됐다. 사무국은 일본산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 오오카 쇼헤(Mr Shohei Ooka)가 책임지고 있다. 현재 의장은 오가타 다카마사(Dr Takamasa Ogata)으로 임기는 2027년까지다.ISO 기술 프로그램 관리자는 주안우 추(Ms Chuanyu Zou), ISO 편집 관리자는 아룬 ABY 파라에카틸(Mr Arun ABY Paraecattil) 등으로 조사됐다.범위는 건축 자재, 부품 및 조립품에 일반적으로 적용되는 비파괴 테스트를 다루는 표준화로 용어집, 테스트 방법, 테스트 장비 및 보조 장치의 성능 사양 등이 포함된다. 단, 품질 수준이나 IEC 위원회의 범위에 속하는 전기 장비 및 장치에 대한 사양은 제외된다.현재 ISO/TC 135 사무국과 관련해 발행된 표준은 97개며 개발중인 표준은 32개다. ISO/TC 135 사무국의 직접적인 책임 하에 발행된 표준 및 개발중인 표준은 각각 1개다. 참여하고 있는 회원은 36개국, 참관 회원은 30개국이다.□ ISO/TC 135 사무국 분과위원회(Subcommittee)의 책임 하에 발행된 표준 목록▷ISO/TS 18173:2005 Non-destructive testing — General terms and definitions□ ISO/TC 135 사무국 분과위원회(Subcommittee)의 책임 하에 개발 중인 표준 목록▷ISO/CD 18173 Non-destructive testing — General terms and definitions□ ISO/TC 135 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 135/SC 2 Surface methods ; 발행된 표준 14개, 개발 중인 표준 1개▷ISO/TC 135/SC 3 Ultrasonic testing ; 발행된 표준 22개, 개발 중인 표준 13개▷ISO/TC 135/SC 4 Eddy current testing ; 발행된 표준 7개, 개발 중인 표준 1개▷ISO/TC 135/SC 5 Radiographic testing ; 발행된 표준 26개, 개발 중인 표준 11개▷ISO/TC 135/SC 6 Leak testing ; 발행된 표준 4개, 개발 중인 표준 1개▷ISO/TC 135/SC 7 Personnel qualification ; 발행된 표준 7개, 개발 중인 표준 0개▷ISO/TC 135/SC 8 Thermographic testing ; 발행된 표준 5개, 개발 중인 표준 0개▷ISO/TC 135/SC 9 Acoustic emission testing ; 발행된 표준 11개, 개발 중인 표준 4개
-
KTC, 중국 인증기관 CVC와 CCC 인증 등 업무협약 체결한국기계전기전자시험연구원(KTC)은 국내 전기·전자 분야 제조업체의 중국 수출을 위해 중국 대표 인증기관인 ‘CVC Certification & Testing Co., Ltd.’(CVC)와 CCC 인증(중국 강제 인증) 및 공장심사에 대한 업무협약을 체결했다고 23일 밝혔다. 이에 국내 전기·전자 분야 제조업체의 중국 수출 경쟁력이 강화될 전망이다. CVC는 중국 대표 시험·인증기관으로 전기, 전자정보통신, 의료, 신재생에너지 등 전 산업 분야에서 중국 수출에 큰 영향을 미치는 CCC 인증 마크를 부여한다. 중국은 자국 내 생산·유통 및 수입되고 있는 전기·전자 제품에 대해 중국 국가표준에 따라 CCC 인증을 의무화하고 있다. 이에 우리나라 전기·전자제품 수출기업은 CCC 인증을 받기 위해 제품을 중국으로 보내 시험을 진행하다 보니 시간과 비용이 많이 소요되어 업계의 부담이 되고 있다. 또한 인증을 받으려면 제품 시험뿐만 아니라 인증 심사원의 공장심사를 거쳐야 한다. 특히 공장심사는 중국 인증기관과 심사원의 스케줄에 따라 변동될 수 있어, 제품 생산과 납품 일정 확보에 어려움을 겪어 왔다. 이번 협약으로 국내 전기·전자 분야 제조업체들은 해외로 시료를 보낼 필요 없이 KTC의 국제공인시험 성적서로 CVC를 통해 CCC 인증을 취득할 수 있게 되고 KTC 직원의 CCC 공장 심사원 등록으로 대중(對中) 수출경쟁력이 강화될 것으로 기대된다. 또한 KTC는 교역 규모 105억 달러로 우리나라의 최대 교역국인 중국과 CCC 인증 이외에도 소프트웨어(SW)·5G(5세대 이동통신)와 전기차 배터리, 충전기, 태양광 모듈·인버터 분야 등에서 상호 협력해 나갈 것을 약속했다. 안성일 KTC 원장은 “우리 기업의 중국진출 시 시험·인증 취득의 어려움을 이번 업무협약을 통해 국내 전기·전자 제조업체의 중국 수출을 지원해 나갈 계획”이라며 “향후 전기차 배터리, 사물인터넷(IoT), 태양광 발전(PV), 반도체 분야로도 서비스 범위를 확대하도록 CVC와 협력 방안을 모색해 나가겠다”고 밝혔다. 한편 KTC는 국내인증산업을 선도하는 글로벌 시험인증기관으로서 기술 장벽이라는 새로운 무역장벽으로 인해 어려움을 겪고 있는 중소기업의 해외 진출을 지원하기 위해 36개국 63개 기관과 업무협약을 체결하고 해외인증 활성화에 앞장서고 있다. 특히 중국에 상해법인과 선전시험소를 둬 국내 기업의 중국 수출의 교두보 역할을 하고 있다.
-
[특집-기술위원회] TC 131 - 유체동력시스템(Fluid power systems)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127 등도 포함된다.ISO/TC 131 유체동력시스템(Fluid power systems)과 관련된 기술위원회는 TC 130과 마찬가지로 1969년에 결성됐다. 사무국은 미국 국립표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 앨리슨 포사이드(Mrs Allison Forsythe)가 책임지고 있다. 현재 의장은 이반 셰필드(Mr Ivan Sheffield)로 임기는 2026년까지다.ISO 기술 프로그램 관리자는 키르시 실란데르-반 후넨(Mrs Kirsi Silander-van Hunen), ISO 편집 관리자는 ISO 편집팀(ISO Editing Team) 등으로 조사됐다.범위는 용어, 구성, 주요 치수, 안전 요구 사항, 테스트 및 검사 방법으로 구성된 유체 동력 시스템 및 구성 요소 분야의 표준화다.TC 131 표준화에 다음과 같은 구성 요소들이 포함된다. △어큐뮬레이터 △압축 공기 건조기 △도체(단단하고 유연한) △실린더 △전기 유압 및 전기 공압 구성 요소와 시스템 △피팅 △유체 장치 △호스 피팅 및 어셈블리 △필터 및 분리기 △유체 △유압 펌프 △모터 △가동부 유체 제어 장치 △공압 윤활 장치 △조절기 △퀵 액션 커플링 △저장소 △밀봉 장치 △밸브 등이다.현재 ISO/TC 131 사무국과 관련해 발행된 표준은 237개며 ISO/TC 131 사무국의 직접적인 책임 하에 발행된 표준은 10개다. ISO/TC 130 사무국과 관련해 개발 중인 표준은 20개다. 참여하고 있는 회원은 16개국, 참관 회원은 19개국이다.□ ISO/TC 130 사무국 분과위원회(Subcommittee)의 책임 하에 발행된 표준 10개 목록▷ISO 2944:2000 Fluid power systems and components — Nominal pressures▷ISO 5352-1:2023 Hydraulic fluid power — Determination of discharge flow rate and thermal losses of gas loaded accumulators — Part 1: Test method▷ISO/TR 10946:2019 Hydraulic fluid power — Gas-loaded accumulators with separator — Selection of preferred hydraulic ports▷ISO/TR 16194:2017 Pneumatic fluid power — Assessment of component reliability by accelerated life testing — General guidelines and procedures▷ISO 19973-1:2015 Pneumatic fluid power — Assessment of component reliability by testing — Part 1: General procedures▷ISO 19973-2:2015 Pneumatic fluid power — Assessment of component reliability by testing — Part 2: Directional control valves▷ISO 19973-2:2015/Amd 1:2019 Pneumatic fluid power — Assessment of component reliability by testing — Part 2: Directional control valves — Amendment 1▷ISO 19973-3:2015 Pneumatic fluid power — Assessment of component reliability by testing — Part 3: Cylinders with piston rod▷ISO 19973-4:2014 Pneumatic fluid power — Assessment of component reliability by testing — Part 4: Pressure regulators▷ISO 19973-5:2015 Pneumatic fluid power — Assessment of component reliability by testing — Part 5: Non-return valves, shuttle valves, dual pressure valves (AND function), one-way adjustable flow control valves, quick-exhaust valves□ ISO/TC 131 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 131/SC 1 Symbols, terminology and classifications ; 발행된 표준 7개, 개발 중인 표준 1개▷ISO/TC 131/SC 2 Pumps, motors and integral transmissions ; 발행된 표준 5개, 개발 중인 표준 0개▷ISO/TC 131/SC 3 Cylinders ; 발행된 표준 24개, 개발 중인 표준 1개▷ISO/TC 131/SC 4 Connectors and similar products and components ; 발행된 표준 50개, 개발 중인 표준 2개▷ISO/TC 131/SC 5 Control products and components ; 발행된 표준 50개, 개발 중인 표준 4개▷ISO/TC 131/SC 6 Contamination control ; 발행된 표준 38개, 개발 중인 표준 5개▷ISO/TC 131/SC 7 Sealing devices ; 발행된 표준 27개, 개발 중인 표준 2개▷ISO/TC 131/SC 8 Product testing ; 발행된 표준 22개, 개발 중인 표준 4개▷ISO/TC 131/SC 9 Installations and systems ; 발행된 표준 4개, 개발 중인 표준 1개□ ISO/TC 131 사무국의 작업그룹(Working Group, WG) 현황▷ISO/TC 131/WG 1 Accumulators▷ISO/TC 131/WG 4 Determination of the reliability of pneumatic components by testing
-
[특집-기술위원회] TC 126 - 담배 및 담배제품(Tobacco and tobacco products)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123 등도 포함된다.ISO/TC 126 담배 및 담배제품(Tobacco and tobacco products)과 관련된 기술위원회는 1968년 결성됐다. 사무국은 독일표준화협회(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 줄리안 정(Mrs Juliane Jung)가 책임지고 있다. 현재 의장은 울프디터 헬러(Mr Prof. Dr Wolf-Dieter Heller)로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 타마호 타카이(Ms Tamaho Takai), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 △분류, 정의 및 용어 △재료 및 특성 △치수 및 공차 △계산 방법을 포함한 테스트 및 품질 관리 방법 등에 대한 플레인 베어링의 표준화다.비제조 담배, 모든 종류의 담배 제품, 담배 제품 제조에 사용되는 재료 및 환경적 담배 연기 측면을 포함한 담배 연기에 대한 용어 및 시험 방법의 표준화다. 취급, 보관, 포장 및 운송에 대한 사양과 질문이 적절하게 포함됐다.담배 제품이란 인간이 사용하도록 의도된 담배로 제조되거나 파생된 모든 제품 및 흡연 또는 무연 제품과 유사한 방식으로 사용되는 제품을 의미한다.현재 ISO/TC 126 사무국과 관련해 발행된 표준은 96개며 ISO/TC 126 사무국의 직접적인 책임하에 발행한 표준은 65개다.ISO/TC 126 사무국과 관련해 개발 중인 표준은 11개며 ISO/TC 126 사무국의 직접적인 책임 하에 개발 중인 표준은 9개다. 참여하고 있는 회원은 30개국, 참관 회원은 35개국이다.□ ISO/TC 126 사무국 분과위원회(Subcommittee)의 책임 하에 발행된 표준 65개 중 15개 목록▷ISO 2881:1992 Tobacco and tobacco products — Determination of alkaloid content — Spectrometric method▷ISO 3308:2012 Routine analytical cigarette-smoking machine — Definitions and standard conditions▷ISO 3400:1997 Cigarettes — Determination of alkaloids in smoke condensates — Spectrometric method▷ISO 3400:1997/Amd 1:2009 Cigarettes — Determination of alkaloids in smoke condensates — Spectrometric method — Amendment 1▷ISO 3401:1991 Cigarettes — Determination of alkaloid retention by the filters — Spectrometric method▷ISO 3402:2023 Tobacco and tobacco products — Atmosphere for conditioning and testing▷ISO 4387:2019 Cigarettes — Determination of total and nicotine-free dry particulate matter using a routine analytical smoking machine▷ISO 4388:1991 Cigarettes — Determination of the smoke condensate retention index of a filter — Direct spectrometric method▷ISO 4389:2000 Tobacco and tobacco products — Determination of organochlorine pesticide residues — Gas chromatographic method▷ISO 6466:1983 Tobacco and tobacco products — Determination of dithiocarbamate pesticides residues — Molecular absorption spectrometric method▷ISO 6488:2021 Tobacco and tobacco products — Determination of water content — Karl Fischer method▷ISO 8243:2013 Cigarettes — Sampling▷ISO 8454:2007 Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method▷ISO 8454:2007/Amd 1:2009 Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method — Amendment 1▷ISO 8454:2007/Amd 2:2019 Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method — Amendment 2□ ISO/TC 126 사무국 분과위원회(Subcommittee)의 책임 하에 개발 중인 표준 9개 목록▷ISO/DIS 5501-1 Tobacco heating systems — Definitions and standard conditions for aerosol generation and collection — Part 1: Electrically Heated Tobacco Products (eHTPs)▷ISO/DIS 5501-2 Tobacco heating systems — Definitions and standard conditions for aerosol generation and collection — Part 2: Aerosol Heated Tobacco Products (aHTPs)▷ISO/DIS 5501-3 Tobacco heating systems — Definitions and standard conditions for aerosol generation and collection — Part 3: Carbon Heated Tobacco Products (cHTPs)▷ISO/AWI 5622 Tobacco heating systems — Carbon monoxide▷ISO/DIS 6080 Tobacco heating systems — Terms and definitions▷ISO/DIS 8454 Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method▷ISO 9322 Material used for producing wrappings for cigarette filters, cigarettes and other tobacco products — Determination of acetate and citrate content — Ion chromatographic method▷ISO/AWI 21109 Nicotine pouches — Test method for pH▷ISO/AWI 21114 Nicotine pouches — Test method for nicotine content□ ISO/TC 126 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 126/SC 1 Physical and dimensional tests ; 발행된 표준 12개, 개발 중인 표준 1개▷ISO/TC 126/SC 2 Leaf tobacco ; 발행된 표준 14개, 개발 중인 표준 0개▷ISO/TC 126/SC 3 Vape and vapour products ; 발행된 표준 5개, 개발 중인 표준 1개□ ISO/TC 126 사무국의 작업그룹(Working Group, WG) 현황▷ISO/TC 126/WG 19 Revision of ISO 15592-3▷ISO/TC 126/WG 22 Tobacco heating systems▷ISO/TC 126/WG 23 Revision of ISO 3402▷ISO/TC 126/WG 24 Nicotine pouches